579 1212 [PDF]

Citation preview

4007ES CPU and Display Board 4007ES NAC PSU (Hybrid)



Jumper J1 Ethernet Port J2 USB Port



J3 Service Mode Jumper



Purpose Used to transfer files to or upload reports from the 4007ES using the Ethernet port on your laptop. This operation requires you to enable the Ethernet port by installing Service Mode Jumper J3..



Connector



Purpose



P2



Serial Interface port is used for connection to remote services.



Used to transfer files to or upload reports from the 4007ES.



P3 & P4



Card Power and Communications connectors. Caution: Locking tabs are located up, on the top of the connectors.



LED 1 2 3 4&5 6



Purpose Ethernet connection LED (ON when connected, blinks with activity) Flashes once a second to show the CPU is processing Flashes once per polling cycle Not used Reset



This jumper is normally positioned on only one of J3’s two pins. When installed, shorting the two pins, the Ethernet Port connection is enabled and a “SERVICE MODE JUMPER INSTALLED” trouble is generated.



SW1 Reset Switch – Cold Start. Clears Disables, Manual Overrides, and Logs U11 - Contains the panel Serial Number and MAC address © 2015 Tyco Fire Protection Products. All rights reserved. All specifications and other information shown were current as of document revision date and are subject to change without notice. TYCO, SIMPLEX, and the product names listed in this material are marks and/or registered marks. Unauthorized use is strictly prohibited.



579-1212 Rev. A



4007ES CPU and Display Board 4007ES NAC PSU (Hybrid) Terminal Blocks on the 4007ES NAC PSU BOARD Terminal(s) Purpose 1-4 IDNet 5&6 Aux/SNAC 7-10 RUI NAC 1 & 2 (Class A operation is software selectable. 1-8 Class B operation has six software selectable EOLs). NAC 3 & 4 (Class A operation is software selectable. 1-8 Class B operation has six software selectable EOLs). 1&2 Battery connection terminals



TB 1 2 3 4



LED LED 1 Aux/SNAC LED 2 RUI Trouble LED 3 Comm LED 4 General Power LED 5 NAC 1 LED 6 RUI OC LED 7 NAC 2 LED 8 NAC 3 LED 9 NAC 4 LED 10 AC Status LED 11 IDNet Loop III LED 12 IDNet Loop II LED 13 IDNet Loop I LED 14 IDNet Earth LED 15 IDNet Earth + LED 16 IDNet LED 17 IDNet Comm



LEDS on the 4007ES NAC PSU BOARD Color Behavior Y Aux Power is Default, 24 volt non-resettable output SNAC operation depends on the selected Point Type Y ON for Class A RUI trouble, otherwise OFF Y ON when offline with Master, otherwise OFF Y ON for AC Power Loss, Earth Fault, Overcurrent Trouble Y ON for OverCurrent, Short, Open Y Fast blink on short (OverCurrent) Y ON for OverCurrent, Short, Open Y ON for OverCurrent, Short, Open Y ON for OverCurrent, Short, Open G OFF on AC Fail, otherwise ON Y A and/or B terminal short, or Class A open trouble Y A and/or B terminal short, or Class A open trouble Y A and/or B terminal short, or Class A open trouble Y Negative Earth Fault Y Positive Earth Fault Y IDNet Channel Fail Y ON when offline with MAster, otherwise OFF



P Connectors on the 4007ES NAC PSU BOARD Purpose RUI Class Selector. Default is Class A. For Class B operation, move the two jumpers to short the top two pins. IDNet+ Loop A Class. Default is Class A. For Class B operation, move the two jumpers to short the top two pins. AC power input connector Connector for ribbon harness to optional city card or optional relay card



P 1 2 10 11



J Connectors on the 4007ES NAC PSU BOARD J



Associated with P



5 7 8 9



4



11 12



6 8



13



9



14



9



15 16 17



Purpose Communications and Power for Zone/Relay card(s) Connector for IDNet Loop B card (first expansion IDNet card) Connector for IDNet Loop C card (second expansion IDNet card) Default - NAC Power Supply Online Jumper removed NAC Power Supply Offline Battery Depleted Jumper - * Canadian operation is not the default jumper setting Default 1-2 IDNet Online Jumper removed IDNET Offline 25V Regulator Jumpers 1-2, 3-4 default. Remove Jumpers and plug in 25V Regulator Harness when using the 25V Regulator Module 25V Regulator Jumpers 1-2, 3-4 default. Remove Jumpers when using the 25V Regulator Module Communications and Power for Zone/Relay card(s) Communications and Power for the retainer mounted CPU card Communications and Power for an option card



579-1212 Rev. A