![Ajax General Catalogue [PDF]](https://pdfs.asia/img/200x200/ajax-general-catalogue.jpg)
13 0 621 KB
Elite
Type Series Booklet
Centrifugal Pump
Application The Ajax Elite centrifugal pump is suitable for handling water and similar liquids mainly used in the following applications. -Water Supply -Air conditioning -Irrigation -Pressure boosting -Fire Protection -Heating and ventilating -Industrial
Design Horizontal, single stage, end suction centrifugal pump, complying with the requirements of EN 733 (DIN 24255). The back pull out design allows for easy maintenance and repair as the rotating element may be removed without disturbing the system pipework. Removal of the rotating element is facilitated by the lifting eye on the bearing housing.
KSB Australia Pty Ltd
Designation E
150 - 40
A
20
C
Type Discharge diameter mm Nominal impeller diameter cm Mechanical arrangement Shaft sealing Materials of construction
Operating Data Pump sizes Flow Head Temperature Speed Pressure
up to up to up to up to up to
50Hz 60Hz 32mm to 250mm 340L/s 288L/s 140m 108m 95oC 2900 rpm 3600 rpm 1600kPa
Elite Selection Chart 1450 rpm
Note: For final selection refer to individual performance curves
Selection Chart 2900 rpm
Note: For final selection refer to individual performance curves
2
Elite Construction
Painting
Horizontal, single stage, end suction with vertical discharge, complying with the requirements of EN 733 (DIN 24255). Most models are suitable for 1600kPa (16 bar) pressure except for larger pumps that are rated for 1000kPa (10 bar). The pull back out design allows for the maintenance of the pump without disturbing the pipework connected to the casing, or the pump alignment.
Prior to painting, the pump is thoroughly cleaned of scale, weld splatter and any other foreign material. The pump is then painted with a high quality industrial enamel paint.
Flanges Pump flanges have raised faces and are to standards AS/NZS 4331.2, ISO 7005.2 16 bar. Gauge tappings are provided on suction and discharge flanges as standard.
Impellers The shrouded impellers have front seals and, either back vanes or rear seals with balance holes to provide hydraulic balance. Impellers are dynamically balanced, are keyed to the shaft and are located axially between the sleeve and impeller nut. Zinc free bronze impellers are fitted as standard.
Casing All pump casings are cast iron and radially split to permit removal of the rotating element. The vertical centre line discharge makes the casing self venting. Zinc free bronze wear rings are fitted as standard.
Shaft Stainless steel shafts are standard and are ground to fit the impeller, sleeve, bearings and coupling.
Bearings Grease Lubrication – Standard Oil Lubrication – for high speed models (EH) Max. Pump Temperature 95oC The Bearing arrangement consists of two identical single row deep groove ball bearings which are grease lubricated through grease nipples located in each bearing cover.
Shaft Seal The shaft sealing is carried out by means of mechanical seal with the option of packed gland. Mechanical Seal - A single mechanical seal, with a ceramic stationary face and carbon rotating face is fitted as standard. The standard seal elastomer is nitrile and is suitable for up to 95oC temperature applications. The other seal components are AISI 304 stainless steel. Options: Balanced seal – option M1 Cyclone separator – option S1 Gland Packing - Fitted with removable lantern ring and square plaited packing. Packing is fitted over the sleeve to prevent shaft wear.
Accessories Drive The pump is only recommended for direct drive via a flexible spacer coupling. Spacer couplings enable the utilisation of the back pull out feature. Where belt drives are necessary a separate jack (intermediate) shaft with bearings to carry the belt loads may be required. All drive systems, where supplied by KSB Ajax, are appropriately protected by suitable guards.
Baseplate Baseplates for electric drives are available in a variety of styles: Standard - Fixed and grouted directly to the foundation. Anti Vibration - Rigid baseplate on rubber mounts. - Rigid baseplate on spring mounts. - Rigid baseplate with inertia block base and spring mounts. The baseplate is manufactured or fabricated from either cold formed (pressed) steel plate or from rolled steel channel sections.
Pump Selection For pump selection the hydraulic performance curves should be used. These curves are based on water at 15oC and SG equal to 1.0. NPSH values are indicated on the performance curves. At least 0.5m should be added as a safety margin. To overcome variations between actual and design system requirements it is recommended that the driver power exceeds the absorbed pump shaft power.
Absorbed Pump
Driver Power
Shaft [kW]
Reserve
Up to 7.5
Approx. 20%
7.5 - 40
Approx. 15%
Above 40
Approx. 10%
3
Elite General Operating Parameters Packed Gland Pressure
Temperature
Speed
Mechanical Seal Standard Seal
Option M1 1400kPa
Maximum operating pressure*
1600kPa
1400kPa
Maximum hydrostatic test pressure
2100kPa
2100kPa
2400kPa
Maximum suction pressure 1450rpm
600kPa
900kPa
1000kPa
Maximum suction pressure 2900rpm
400kPa
700kPa
1000kPa
Packed gland
-20oC to 95oC
Mechanical Seal: Standard
-20oC to 95oC
Mechanical Seal Balanced: Option M1 Maximum Speed*
-20oC to 95oC 3600 rpm
*refer tabular listing on page 5.
Material Specifications Material
Component
Cast Iron
Casing
Nearest Equivalent Standard Australian
British
American
EN
AS1830/T220
BS1452: GR220
ASTM A48 Class 30
JL 1030
CT1
ASTM C 90700
CC480 K - GC
AS1565-C83600
906D BS1400-LG2
ASTM B584-C83600
-
AS2837 GR.420 AS2837 GR.316
BS970:420/S37 BS970:316
AISI Type 420 AISI Type 316
X20CR13 X10CRN1MOT118/10
Back Cover Bearing Housing Bearing Cover Lantern Ring Wear Rings (Option) Zinc Free Bronze
Impeller
AS1565-1985 Alloy C90250
Wear Rings
Lantern Ring Bush Bronze Stainless Steel Shaft Shaft Sleeve
BS 1400-1973
Pump Material Combinations Part
Mechanical Seal
Packed Gland
Packed Gland
Description
Code 04 (A20C)
Code 07 (AXOC)
Code 09 (AXOJJ)
Casing
Cast Iron
Cast Iron
Stainless Steel
Impeller
Zinc Free Bronze
Zinc Free Bronze
Stainless Steel
Wear Rings
Zinc Free Bronze
Zinc Free Bronze
Stainless Steel
Shaft
Stainless Steel
Stainless Steel
420 Stainless Steel
Shaft Sleeve
Not Fitted
Stainless Steel
Stainless Steel
Spring Sleeve
Stainless Steel
Not Fitted
Not Fitted
Lantern Ring
Not Fitted
Cast Iron
Stainless Steel
Lantern Ring Bush
Not Fitted
Bronze
Stainless Steel
Gland Seal Plate
Not Fitted Cast Iron
Cast Iron Not Fitted
Stainless Steel Not Fitted
Mechanical Seal Materials Part Description Seat Seal Face Seal O Ring Bellows Retainer Drive Band Spring Holder Spring
Standard
High Pressure Option M1
Ceramic Carbon Nitrile Nitrile
Silicon Cabid Carbon Nitrile Nitrile
Stainless Steel AISI 304
Stainless Steel AISI 316
4
Elite Pump Technical Data
Maximum Nominal Pump Model Speed Direct Coupled
Bearing Type
Mass Moment of Inertia J Rotating Assy. Less Coupling [kg*m 2]
Hydrostatic Test Pressure Maximum
Maximum Working Pressure up to 120˚C
rpm/imp. dia
Front
Rear
Bronze Impeller
bar
kPa
PSI
bar
kPa
PSI
E32-13
3450/134
6305
6305
0.004
21
2100
304
16
1600
232
E32-16
3450/156
6305
6305
0.006
21
2100
304
16
1600
232
E32-20
3450/181
6305
6305
0.015
21
2100
304
16
1600
232
E32-26
3450/220
6305
6305
0.043
21
2100
304
16
1600
232
E40-13
3450/130
6305
6305
0.004
21
2100
304
16
1600
232
E40-16
3450/156
6305
6305
0.006
21
2100
304
16
1600
232
E40-20
3450/186
6305
6305
0.019
21
2100
304
16
1600
232
E40-26
3450/225
6305
6305
0.048
21
2100
304
16
1600
232
E40-32
2300/329
6307
6307
0.105
21
2100
304
16
1600
232
EH40-32
2900/320
3307
3307
0.105
21
2100
304
16
1600
232
E50-13
3450/132
6305
6305
0.005
21
2100
304
16
1600
232
E50-16
3450/159
6305
6305
0.008
21
2100
304
16
1600
232
E50-20
3450/182
6305
6305
0.019
21
2100
304
16
1600
232
E50-26
3450/227
6305
6305
0.05
21
2100
304
16
1600
232
E50-32
2300/328
6307
6307
0.111
21
2100
304
16
1600
232
EH50-32
2900/314
3307
3307
0.111
21
2100
304
16
1600
232
E65-13
3450/159
6305
6305
0.006
21
2100
304
16
1600
232
E65-16
3450/159
6305
6305
0.009
21
2100
304
16
1600
232
E65-20
3450/184
6305
6305
0.019
21
2100
304
16
1600
232
E65-26
3450/224
6307
6307
0.052
21
2100
304
16
1600
232
E65-32
2400/329
6307
6307
0.127
21
2100
304
16
1600
232
EH65-32
2900/316
3307
3307
0.127
21
2100
304
16
1600
232
E80-16
3450/160
6305
6305
0.013
21
2100
304
16
1600
232
E80-20
3450/191
6307
6307
0.024
21
2100
304
16
1600
232
E80-26
3450/230
6307
6307
0.05
21
2100
304
16
1600
232
E80-32
1800/329
6307
6307
0.107
21
2100
304
16
1600
232
EH80-32
2900/318
3307
3307
0.107
21
2100
304
16
1600
232
E80-40
1800/409
6309
6309
0.392
17
1700
246
13
1300
188
E100-16
2900/174
6307
6307
0.02
21
2100
304
16
1600
232
E100-20
3450/193
6307
6307
0.03
21
2100
304
16
1600
232
E100-26
3450/228
6307
6307
0.068
21
2100
304
16
1600
232
E100-32
1800/329
6307
6307
0.156
21
2100
304
16
1600
232
E100-40
1800/409
6309
6309
0.358
17
1700
246
13
1300
188
E125-20
2900/214
6307
6307
0.069
21
2100
304
16
1600
232
E125-26
1800/264
6307
6307
0.076
21
2100
304
16
1600
232
E125-32
1800/329
6309
6309
0.165
21
2100
304
16
1600
232
E125-40
1800/409
6309
6309
0.377
17
1700
246
13
1300
188
E150-20
1800/220
6307
6307
0.078
15
1500
217
11
1100
159
E150-26
1800/264
6309
6309
0.158
15
1500
217
11
1100
159
E150-32
1800/329
6309
6309
0.182
15
1500
217
11
1100
159
E150-40
1800/409
6309
6309
0.4
15
1500
217
11
1100
159
E200-26
1800/264
6309
6309
0.3
15
1500
217
11
1100
159
E200-32
1800/329
6311
6311
0.217
15
1500
217
11
1100
159
E200-40
1800/409
6311
6311
0.441
15
1500
217
11
1100
159
E250-32 E250-40
1800/329 1800/409
6311 6311
6311 6311
0.221 0.451
15 15
1500 1500
217 217
11 11
1100 1100
159 159
5
Elite Pump Technical Data B.P.O
Impeller Data Seal Ring
Bearing
Expeller Vane
Pump
Diametrical
Diameter
Model
Clearance
[mm]
[mm]
Vane Width [mm]
No. of Vanes [mm]
Front Seal Back Seal Eye Diameter Diameter Diameter [mm] [mm] [mm]
Element Weight [kg] Dia. [mm]
No. of Vanes
Height [mm]
(Pump Less
Max.
Min.
Max.
Min.
E32-13*
0.4
0.3
139
100
7
6
61
70
-
-
-
-
Casing)
20
E32-16
0.4
0.3
174
125
6
6
62
70
-
120
6
3
25
E32-20
0.4
0.3
214
165
6
4
68
80
-
140
8
3
32 43
E32-26
0.4
0.3
264
205
5
6
70
80
-
200
6
4
E40-13*
0.4
0.3
139
100
10
6
71
80
-
-
-
-
20
E40-16
0.4
0.3
175
130
7.5
6
68
80
-
114
8
3.5
25
E40-20
0.4
0.3
214
165
7
6
69
80
-
153
8
3
33
E40-26
0.4
0.3
264
205
6
6
84
95
-
168
8
5
44
E40-32
0.4
0.3
329
255
6
6
77
95
95
-
-
-
59
EH40-32
0.4
0.3
320
255
6
6
77
95
95
-
-
-
59
E50-13
0.4
0.3
139
120
16
6
88
95
-
126
6
3
22
E50-16
0.4
0.3
174
135
13
6
85
95
-
164
6
2.5
26
E50-20
0.4
0.3
214
165
10
6
86
95
-
154
8
3
33
E50-26
0.4
0.3
264
205
8
7
94
115
-
189
8
5.5
45
E50-32
0.4
0.3
328
255
7
6
102
115
115
-
-
-
56
EH50-32
0.4
0.3
314
255
7
6
102
115
115
-
-
-
56
E65-13
0.4
0.3
139
130
23
7
100
115
-
139
6
4.5
24
E65-16
0.4
0.3
174
125
19
6
102
115
-
139
6
6
28
E65-20
0.4
0.3
214
165
16
6
107
115
-
180
8
4
35
E65-26
0.4
0.3
264
205
13
6
108
115
-
228
8
2
66
E65-32
0.5
0.4
329
255
10
7
114
130
125
-
-
-
73
EH65-32
0.5
0.4
316
255
10
7
114
130
125
-
-
-
73
E80-16
0.5
0.4
174
145
25
7
118
130
-
151
8
5
31
E80-20
0.5
0.4
214
165
22
6
121
130
-
186
8
4
46
E80-26
0.5
0.4
264
205
15
7
120
130
-
247
8
4
62
E80-32
0.5
0.4
329
255
13
6
125
140
135
-
-
-
74
EH80-32
0.5
0.4
318
255
13
6
125
140
135
-
-
-
74
E80-40
0.5
0.4
409
320
11
7
128
140
160
-
-
-
107
E100-16
0.5
0.4
174
165
32
7
148
160
-
164
9
4.5
20
E100-20
0.5
0.4
214
175
27
7
142
160
-
208
9
4
50
E100-26
0.5
0.4
264
205
23
7
145
160
-
253
10
5.5
56
E100-32
0.5
0.4
329
255
18
7
144
160
155
-
-
-
87
E100-40
0.5
0.4
409
320
15
6
147
160
160
-
-
-
120
E125-20
0.5
0.4
214
190
34
7
167
180
-
205
12
2
62
E125-26
0.5
0.4
264
205
32
6
167
180
-
236
12
3
67
E125-32
0.5
0.4
329
255
23
6
167
180
180
-
-
-
97
E125-40
0.5
0.4
409
320
20
7
166
180
180
-
-
-
122
E150-20
0.5
0.4
220
200
57
6
170
185
185
-
-
-
88
E150-26
0.5
0.4
264
210
39
7
185
200
200
-
-
-
93
E150-32
0.5
0.4
329
255
31
6
183
200
200
-
-
-
102
E150-40
0.5
0.4
409
320
26
7
188
200
200
-
-
-
125
E200-26
0.5
0.4
264
250
68
6
220
235
200
-
-
-
86
E200-32
0.5
0.4
329
285
50
6
232.5
250
250
-
-
-
153
E200-40
0.5
0.4
409
335
37.5
7
222
235
235
-
-
-
180
E250-32 E250-40
0.5 0.5
0.4 0.4
329 409
285 335
72 52
6 6
242 236
260 260
260 260
-
-
-
190 237
* no Expeller Vanes
6
Elite Parts List and Material Identification Packed Gland Arrangement
Pump Model:
Pump Model:
E40-32, E50-32, E65-32, E80-32, E80-40, E100-32,
E32-13*, E32-16, E32-20, E32-26, E40-13*, E40-16, E40-20,
E100-40, E125-32, E125-40, E150-20, E150-26, E150-32,
E40-26, E50-13, E50-16, E50-20, E50-26, E65-13, E65-16,
E150-40, E200-26, E200-32, E200-40, E250-32, E250-40
E65-20, E65-26, E80-16, E80-20, E80-26, E100-16, E100-20, E100-26, E125-20, E125-26
Pump Models with clamped back cover:
Pump Models with bolted back cover:
E32-13, E32-16, E40-13, E40-16,
E32-20, E32-26, E40-20, E40-26, E40-32,
E50-13, E50-16, E65-13, E65-16,
E50-20, E50-26, E50-32, E65-20, E65-26,
E80-16, E80-20, E100-16, E100-20,
E65-32, E80-26, E80-32, E80-40, E100-26,
E125-20, E150-26, E200-26
E100-32, E100-40, E125-26, E125-32, E125-40, E150-20, E150-32, E150-40, E200-32, E200-40, E250-32, E250-40
* no Expeller Vanes
ITEM
DESCRIPTION
MATERIAL
ITEM
DESCRIPTION
MATERIAL
1A
Casing
Cast Iron
40.7
Gasket, Flange Plug
Bonded Fibre
2A
Impeller
Zinc Free Bronze
42.1
Wear Ring, Casing
Zinc Free Bronze
3A
Backcover
Cast Iron
42.2
Wear Ring, Backcover
Zinc Free Bronze
10
Bearing Housing
Cast Iron
43
Seal, Bearing Cover
Felt*
11.1/.2
Bearing Cover
Cast Iron
73
Support Foot
Steel
20
Shaft
Stainless Steel
82.1
Plug, Casing Drain
Malleable Iron
21
Impeller Nut
Bronze
82.2
Plug, Flange
Malleable Iron
25
Slinger
Rubber
85
Grease Nipple
Steel
28.1
Key, Impeller
Key Steel
90.1
Stud, Casing
Steel
28.2
Key, Coupling
Key Steel
90.2
Stud, Backcover
Steel
29
Bearing
Steel
90.3
Stud, Gland
Steel
30
Gland
Cast Iron
92
Setscrew, Bearing Cover
Steel
31
Lantern Ring Bush
Bronze
93
Setscrew, Support Foot
Steel
31A
Lantern Ring
Cast Iron
94.1
Nut, Casing Stud
Steel
32
Shaft Sleeve
Stainless Steel
94.2
Nut, Backcover Stud
Steel
34
Gland Packing
Graphited Fibre
94.3
Nut, Gland Stud
Steel
40**
Gasket, Casing
Bonded Fibre/NBR
97
Washer, Impeller Nut
Brass
40.6
Gasket, Drain Plug
Bonded Fibre
*Note: Lip Seals fitted to pump models E80-40, E100-40, E125-32, E125-40, E150-32, E150-40, E200-26, E200-32, E200-40, E250-32, E250-40
**From 1997 O Ring used instead of gasket.
7
Elite Parts List and Material Identification Mechanical Seal Arrangement
Pump Model:
Pump Model:
E40-32, E50-32, E65-32, E80-32, E80-40, E100-32,
E32-13*, E32-16, E32-20, E32-26, E40-13*, E40-16, E40-20,
E100-40, E125-32, E125-40, E150-20, E150-26, E150-32,
E40-26, E50-13, E50-16, E50-20, E50-26, E65-13, E65-16,
E150-40, E200-26, E200-32, E200-40, E250-32, E250-40
E65-20, E65-26, E80-16, E80-20, E80-26, E100-16, E100-20, E100-26, E125-20, E125-26
Pump Models with clamped back cover:
Pump Models with bolted back cover:
E32-13, E32-16, E40-13, E40-16,
E32-20, E32-26, E40-20, E40-26, E40-32,
E50-13, E50-16, E65-13, E65-16,
E50-20, E50-26, E50-32, E65-20, E65-26,
E80-16, E80-20, E100-16, E100-20,
E65-32, E80-26, E80-32, E80-40, E100-26,
E125-20, E150-26, E200-26
E100-32, E100-40, E125-26, E125-32, E125-40, E150-20, E150-32, E150-40, E200-32, E200-40, E250-32, E250-40
* no Expeller Vanes
ITEM
DESCRIPTION
MATERIAL
ITEM
DESCRIPTION
MATERIAL
1A
Casing
Cast Iron
41
O Ring Seal Plate
Nitrile
2A
Impeller
Zinc Free Bronze
42.1
Wear Ring, Casing
Zinc Free Bronze
3A
Backcover
Cast Iron
42.2
Wear Ring, Backcover
Zinc Free Bronze
10
Bearing Housing
Cast Iron
43
Seal, Bearing Cover
Felt*
11.1/.2
Bearing Cover
Cast Iron
73
Support Foot
Steel
20
Shaft
Stainless Steel
82.1
Plug, Casing Drain
Malleable Iron
21
Impeller Nut
Bronze
82.2
Plug, Flange
Malleable Iron
25
Slinger
Rubber
85
Grease Nipple
Steel
28.1
Key, Impeller
Key Steel
90.1
Stud, Casing
Steel
28.2
Key, Coupling
Key Steel
90.2
Stud, Backcover
Steel
29
Bearing
Steel
90.3
Stud, Gland
Steel
35
Mechanical Seal
Carbon/Ceramic
92
Setscrew, Bearing Cover
Steel
36
Spring Sleeve
Stainless Steel
93
Setscrew, Support Foot
Steel
37
Seal Plate
Cast Iron
94.1
Nut, Casing Stud
Steel
40**
Gasket, Casing
Bonded Fibre/NBR
94.2
Nut, Backcover Stud
Steel
40.6
Gasket, Drain Plug
Bonded Fibre
94.3
Nut, Gland Stud
Steel
40.7
Gasket, Flange Plug
Bonded Fibre
97
Washer, Impeller Nut
Brass
*Note: Lip Seals fitted to pump models E80-40, E100-40, E125-32, E125-40, E150-32, E150-40, E200-26, E200-32, E200-40, E250-32, E250-40 **From 1997 O Ring used instead of gasket.
8
Elite ROTATION
DISCHARGE
Dimensions FLANGES DRILLED TO AS/NZS 4331.2 (ISO 7005.2-16bar) SUCTION
END ELEVATION PUMP SIZE
SHAFT SUCT. DISCH.
SIDE ELEVATION
PUMP
SPACER
FOOT
MODULE a
f
h1
h2
b
m1
m2
n1
n2
n3
h3
s1
s2
w
p
SHAFT
COUPLING
NET
END
KEY
WEIGHT
y
d
l
[kg]
E32-13
25
50
32
80 360 112 140 50 100 70 190 140 100 14
14
14 267 80
100
24
50
8x7
27
E32-16
25
50
32
80 360 132 160 50 100 70 240 190 100 14
14
14 267 80
100
24
50
8x7
35
E32-20
25
50
32
80 360 160 180 50 100 70 240 190 110 14
14
14 267 80
100
24
50
8x7
41
E32-26
25
50
32
100 360 180 225 65 125 95 320 250 110 14
14
14 267 100
100
24
50
8x7
59
E40-13
25
65
40
80 360 112 140 50 100 70 210 160 100 14
14
14 267 80
100
24
50
8x7
30
E40-16
25
65
40
80 360 132 160 50 100 70 240 190 100 14
14
14 267 80
100
24
50
8x7
36
E40-20
25
65
40
100 360 160 180 50 100 70 265 212 110 14
14
14 267 100
100
24
50
8x7
44
E40-26
25
65
40
100 360 180 225 65 125 95 320 250 110 14
14
14 267 100
100
24
50
8x7
61
E40-32
35
65
40
125 470 200 225 65 130 95 345 280 110 14
14
14 342 125
140
32
80
10x8
96
EH40-32
35
65
40
125 470 200 225 65 130 95 345 280 110 14
14
14 342 125
140
32
80
10x8
96
E50-13
25
65
50
100 360 132 160 50 100 70 240 190 100 14
14
14 267 100
100
24
50
8x7
34
E50-16
25
65
50
100 360 160 180 50 100 70 265 212 110 14
14
14 267 100
100
24
50
8x7
38
E50-20
25
65
50
100 360 160 200 50 100 70 265 212 110 14
14
14 267 100
100
24
50
8x7
46
E50-26
25
65
50
100 360 180 225 65 125 95 320 250 110 14
14
14 267 100
100
24
50
8x7
63
E50-32
35
65
50
125 470 225 280 65 125 95 345 280 110 16
14
14 342 124
140
32
80
10x8
101
EH50-32
35
65
50
125 470 225 280 65 125 95 345 280 110 16
14
14 342 124
140
32
80
10x8
101
E65-13
25
80
65
100 360 160 180 65 125 95 280 212 110 14
14
14 267 100
100
24
50
8x7
39
E65-16
25
80
65
100 360 160 200 65 125 95 280 212 110 14
14
14 267 100
100
24
50
8x7
43
E65-20
25
80
65
100 360 180 225 65 125 95 320 250 110 14
14
14 267 100
100
24
50
8x7
70
E65-26
35
80
65
100 470 200 250 80 160 120 360 280 110 16
18
14 342 100
140
32
80
10x8
81
E65-32
35
80
65
125 470 225 280 80 160 120 400 315 110 16
18
14 342 125
140
32
80
10x8
110
EH65-32
35
80
65
125 470 225 280 80 160 120 400 315 110 16
18
14 342 125
140
32
80
10x8
110
E80-16
25
100
80
125 360 180 225 65 125 95 320 250 110 14
14
14 267 125
100
24
50
8x7
54
E80-20
35
100
80
125 470 180 250 65 125 95 345 280 110 14
14
14 342 125
140
32
80
10x8
70
E80-26
35
100
80
125 470 200 280 80 160 120 400 315 110 16
18
14 342 125
140
32
80
10x8
91
E80-32
35
100
80
125 470 250 315 80 160 120 400 315 110 16
18
14 342 125
140
32
80
10x8
120
EH80-32
35
100
80
125 470 250 315 80 160 120 400 315 110 16
18
14 342 125
140
32
80
10x8
120
E80-40
45
100
80
125 532 280 365 85 160 120 440 340 110 19
18
14 368 132
140
42
110
12x8
161
E100-16
35
125
100
125 470 200 280 30 160 120 340 260 110 16
18
14 342 125
140
32
80
10x8
71
E100-20
35
125
100
125 470 200 280 80 160 120 360 280 110 16
18
14 342 125
140
32
80
10x8
85
E100-26
35
125
100
140 470 225 280 80 160 120 400 315 110 16
18
14 342 140
140
32
80
10x8
106
E100-32
35
125
100
140 470 250 315 80 160 120 400 315 110 16
18
14 342 140
140
32
80
10x8
134
E100-40
45
125
100
140 530 280 355 100 200 150 500 400 110 18
23
14 370 140
140
42
110
12x8
174
E125-20
35
150
125
140 470 250 315 80 160 120 400 315 110 16
18
14 342 140
140
32
80
10x8
106
E125-26
35
150
125
140 470 250 355 80 160 120 400 315 110 16
18
14 342 140
140
32
80
10x8
115
E125-32
45
150
125
140 530 280 355 100 200 150 500 400 110 18
23
14 370 140
140
42
110
12x8
163
E125-40
45
150
125
140 530 315 400 100 200 150 500 400 110 18
23
14 370 140
140
42
110
12x8
181
E150-20
35G
200
150
160 495 280 400 100 200 150 550 450 110 20
23
14 367 160
140
32
80
10x8
156
E150-26
45
200
150
160 530 250 355 100 200 150 450 350 110 18
23
14 370 160
140
42
110
10x8
148
E150-32
45
200
150
160 530 280 400 100 200 150 550 450 110 18
23
14 370 160
140
42
110
12x8
170
E150-40
45
200
150
160 530 315 450 100 200 150 550 450 110 18
23
14 370 160
140
42
110
12x8
209
E200-26
45D
250
200
180 553 315 450 100 200 150 550 450 110 20
28
14 393 180
180
42
110
12x8
206
E200-32
55
250
200
180 670 315 480 120 220 170 600 480 110 20
28
14
504 180
180
48
110
14x9
251
E200-40
55
250
200
180 670 335 480 120 220 170 600 480 110 20
28
14
504 180
180
48
110
14x9
295
E250-32 E250-40
55 55
300 300
250 250
220 691 355 520 150 250 200 660 510 110 22 220 682 400 560 150 250 200 660 510 110 22
28 28
14 14
525 220 516 220
180 180
48 48
110 110
14x9 14x9
311 390
Dimensions shown in mm
9
Elite Flange Data Raised Face Drilling* Flange Branch Size D b d1 f d2 k N0. 4 32 140 18 78 2 18 100 4 40 150 18 88 3 18 110 4 50 165 20 102 3 18 125 4 65 185 20 122 3 18 145 80 200 22 138 3 18 160 8 8 100 220 24 158 3 18 180 125 250 26 188 3 18 210 8 150 285 26 212 3 22 240 8 200 340 32 268 3 22 295 12 250 405 32 320 3 26 355 12 300 460 32 378 4 26 410 12 Flange dimensions and drilling according to AS/NZS 4331.2, ISO 7005.2 - 16 bar (BS4504 - 1969 Table 16/11, DIN 2533 PN16) Dimensions shown in mm *Holes - Equally spaced straddling pump centreline
Shaft Dimensions
Bolting M16 M16 M16 M16 M16 M16 M16 M20 M20 M24 M24
Shaft Module
KEY LENGTH KEY WIDTH KEY HEIGHT
SEAT DEPTH
Key Key Key Diameter D Tol Length Height Width Nom -0.004 32 8 7 25 24 +0.009 -0.002 8 10 35 40 32 +0.018 -0.002 8 12 45 50 42 +0.018 -0.002 9 14 80 48 55 +0.018 Key dimensions are in nominal and expressed in mm
Seat Depth 20 27 37 42.5
Service Connections PUMP MODEL
A
B*
CASING HOUSING DRAIN
DRAIN
E32-13 1/4 3/8 E32-16 1/4 3/8 E32-20 1/4 3/8 E32-26 3/8 3/8 E40-13 1/4 3/8 E40-16 1/4 3/8 E40-20 1/4 3/8 E40-26 3/8 3/8 E40-32 3/8 3/8 EH40-32 3/8 3/8 E50-13 1/4 3/8 E50-16 3/8 3/8 E50-20 1/4 3/8 E50-26 3/8 3/8 E50-32 3/8 3/8 EH50-32 3/8 3/8 E65-13 1/4 3/8 E65-16 3/8 3/8 E65-20 3/8 3/8 E65-26 3/8 3/8 E65-32 3/8 3/8 EH65-32 3/8 3/8 E80-16 3/8 3/8 E80-20 3/8 3/8 Dimensions shown in inch
D
S
PUMP
GAUGE
GAUGE
MODEL
TAPPING TAPPING
1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4
1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4
E80-26 E80-32 EH80-32 E80-40 E100-16 E100-20 E100-26 E100-32 E100-40 E125-20 E125-26 E125-32 E125-40 E150-20 E150-26 E150-32 E150-40 E200-26 E200-32 E200-32 E200-40 E250-32 E250-40
A
B*
CASING HOUSING
D
S
GAUGE
GAUGE
DRAIN
DRAIN
TAPPING
TAPPING
3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8
3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 1/2 3/8 3/8 3/8 3/8 3/8
1/4 3/8 3/8 1/4 1/4 1/4 3/8 3/8 1/4 3/8 3/8 3/8 3/8 1/4 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8
1/4 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8
ROTATION
END ELEVATION DISCHARGE
SUCTION
SIDE ELEVATION
*Left side view from suction
10
Elite Nominal Stuffing Box Dimensions
From end of stuffing box.
MODULE 25 & 35
NOTE: Only some models have combination lantern ring-register bush, check assembly drawing.
MODULE 45 & 55
Module
L
L1
L2
d
d1
d2
k
f
g
25 35 45 55
44 53* 63 80
30 40* 46 62
56 63** 78 62
48 60 75 90
32 40 54 65
24 32 44 53
85 100 110 130
M8 M10 M12 M12
35 40 50 55
*: models E40-32, E50-32, E65-32, E80-32, E100-32, E100-32, E125-26 L=63, L1=50, No. Rings=4 **: model E150-20 L2=83
Packing Size No. rings 8 Sq 3 10 Sq 3* 10 Sq 4 13Sq 4 Dimensions shown in mm
Mechanical Seal, A20 - Conversion Kits The kit is suitable to convert standard packed gland pumps. The kit comprises of mechanical seal, spring sleeve, seal plate, O ring seal and nameplate. Pump Size E32-13/16/20/26 E40-13/16/20/26 E50-13/16/20/26 E65-13/16/20 E80-16 E40-32, EH40-32 E50-32, EH50-32 E65-26/32, EH 65-32 E80-20/26/32, EH80-32 E100-16/20/26/32 E125-20/26 E150-20 E80-40 E100-40 E125-32/40 E150-26/32/40 E200-26 E200-32 E200-40 E250-32 E250-40
Module
Conversion Kit No.
25
213591
35
213592
35G
213592G
Parts included in kit Mechanical Seal 213524 Spring Sleeve 36-25-HF Seal Plate 21371HA O ring BS-225-GM Nameplate 218003 Mechanical Seal 213532 Spring Sleeve 21361HF (35) 36-35G-HF (35G) Seal Plate 21372HA O ring BS-229-GM Nameplate 218003 Mechanical Seal Spring Sleeve
45
213593
45D
213593D
55
213594
Seal Plate O ring Nameplate Mechanical Seal Spring Sleeve Seal Plate O ring Nameplate
213544 36-45-HF (45) 36-45D-HF (45D) 21373HA BS-233-GM 218003 213553 36-55-HF 21374HA BS-238-GM 218003
11
Elite
Type Series Booklet
KSB Australia Pty Ltd ABN: 29 006 414 642 Victorian Head Office
New South Wales
Queensland
South Australia
Western Australia
27 Indwe St,
Unit 1, 28 Skinner Ave,
53 Jijaws St,
Unit 4, 348 Richmond Rd,
Unit 2, 86 Catalano Circuit, Unit 2, 5 Civil Place,
New Zealand
Tottenham, 3012
Riverwood, 2210
Sumner Park, 4074
Netley, 5037
Canning Vale, 6155
Albany, Auckland 1331
Tel: +61 (03) 9314 0611
Tel: +61 (02) 9584 2099
Tel: +61 (07) 3725 8200
Tel: +61 (08) 8234 0066
Tel: +61 (08) 9455 7900
Tel: +64 (09) 476 4047
Fax: +61 (03) 9314 7435
Fax: +61 (02) 9584 2111
Fax: +61 (07) 3725 8299
Fax: +61 (08) 8443 5411
Fax: +61 (08) 9455 7800
Fax: +64 (09) 476 4048
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
WEBSITE: www.ksbajax.com.au Due to our policy of constant research and development, product specification may change without notice
24 HOUR EMERGENCY SERVICE LINE: 1300 301 356 Publication 2007 02/14 1/2K AGP
