Kode Error UW-500 [PDF]

Citation preview

UW-500 CURRENCY SORTER



Kode Error



DETAIL ERROR ERROR TYPE



sensor error: sensor ON check error Abstruct



Check timing



Transmitter of sensor emits light with maximum power but can’t detect at receiver.



Code, Sensor name, Content 2001 2002 2003 2004 2007 2008 2009 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020 2021 2022 2023 2024 2025 2026 2027 2028 2029 2030 2031 2032 2033 2034 2035 2036



PSA01 : stack detection of HP PSB01L : skew detection (L) PSB01C : skew detection (C) PSB01R : skew detection (R) PSB03L : begin to trace (L) PSB03R : begin to trace (R) PSB04 : remain detection of HP VP1L : pass detection of verification block (1L) VP1R : pass detection of verification block (1R) VP3L : pass detection of verification block (2L) VP3R : pass detection of verification block (2R) thickness : thickness detection TMP/HUM : temperture / humidity HUM : humidity LS : line sensor FPGA : FPGA G/A2 : gate array (IC2) G/A3 : gate array (IC3) FAN : FAN TMFL : magnetism sensor (L) TMFR : magnetism sensor (R) UVT : UV sensor FLR : UV sensor LSA : line sensor of verification block (LSA) LSB : line sensor of verification block (LSB) UV : sub sensor of verification block (1UV) FL : sub sensor of verification block (1FL) GSL : sub sensor of verification block (1GSL) GSR : sub sensor of verification block (1GSR) MG : sub sensor of verification block (1MG) TC : sub sensor of verification block (2TC) USR : sub sensor of verification block (2USR) USL : sub sensor of verification block (2USL)



Error cause



on reset begin process after changing process mode in aging



Method of check



Measures



dirt sensor, flawing, adhesion of foreign matter



Visually check around sensor



Clean sensor or replace Remove foreign matter Correct to set or replace sensor



gap optical axis



Visually check to state of setting sensor and bracket deformation Visually check around sensor



replace bracket Check guide plate and belt



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



sensor level error



Check to display sensor level(RAS)



Clean sensor



sensor defection



Check to “PORT READ”(RAS) Check port which change sensor status



Adjust sensor or replace



deformation of guide plate come off belt、expand come off connector breaking of wire



Replace verification unit defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Resume process Open unit of error cause and close it. After it, press CLEAR key.



ERROR TYPE



sensor error: sensor ON check error Abstruct



Check timing



Transmitter of sensor emits light with maximum power but can’t detect at receiver.



Code, Sensor name, Content 2037 2038 2039 2040 2042 2043 2044 2045 2046 2048 2049 2050 2051 2052 2055 2057 2058 2060 2061 2063 2064 2066 2067 2068 2069 2070 2071 2072 2073 2074 2081 2083 2084 2086



PSD01L : BVREQ timing detection (L) PSD01R : BVREQ timing detection (R) PSD02L : RJ1 branch timing detection (L) PSD02R : RJ1 branch timing detection (R) PSD03 : RJ1 approaching detection PSD04L : RJ1 bill remaining detection (L) PSD04R : RJ1 bill remaining detection (R) PSD05L : RJ2 branch timing detection (L) PSD05R : RJ2 branch timing detection (R) PSD06 : RJ2 approaching detection PSD07L : RJ2 bill remaining (L) PSD07R : RJ2 bill remaining (R) PSD08 : check branch of transfer PSD09 : pass detection of joint part PSE01 : stacker1 branch timing detection PSE02 : stacker1 approaching detection PSE03 : stacker2 branch timing detection PSE04 : stacker2 approaching detection PSE05 : stacker3 branch timing detection PSE06 : stacker3 approaching detection PSE07 : stacker4 branch timing detection PSE08 : stacker4 approaching detection PSE09 : stacker1 bill remaining detection PSE10 : stacker1 bill remaining detection PSE11 : stacker2 bill remaining detection PSE12 : stacker2 bill remaining detection PSE13 : stacker3 bill remaining detection PSE14 : stacker3 bill remaining detection PSE15 : stacker4 bill remaining detection PSE16 : stacker4 bill remaining detection PSE17 : stacker5 branch timing detection PSE18 : stacker5 approaching detection PSE19 : stacker6 branch timing detection PSE20 : stacker6 approaching detection



Error cause



on reset begin process after changing process mode in aging



Method of check



Measures



dirt sensor, flawing, adhesion of foreign matter



Visually check around sensor



Clean sensor or replace Remove foreign matter Correct to set or replace sensor



gap optical axis



Visually check to state of setting sensor and bracket deformation Visually check around sensor



replace bracket Check guide plate and belt



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



sensor level error



Check to display sensor level(RAS)



Clean sensor



sensor defection



Check to “PORT READ”(RAS) Check port which change sensor status



Adjust sensor or replace



deformation of guide plate come off belt、expand come off connector breaking of wire



Replace verification unit defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board) (1) (2) (1) (2) (1) (2) (1) (2)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Resume process Open unit of error cause and close it. After it, press CLEAR key.



ERROR TYPE



sensor error: sensor ON check error Abstruct



Check timing



Transmitter of sensor emits light with maximum power but can’t detect at receiver.



Code, Sensor name, Content 2087 2089 2090 2092 2093 2094 2095 2096 2097 2098 2099 2100 2124 2125 2126 2127 2128 2129



PSE21 : stacker7 PSE22 : stacker7 PSE23 : stacker8 PSE24 : stacker8 PSE25 : stacker5 PSE26 : stacker5 PSE27 : stacker6 PSE28 : stacker6 PSE29 : stacker7 PSE30 : stacker7 PSE31 : stacker8 PSE32 : stacker8 HL1 : half-locked



Error cause



branch timing detection approaching detection branch timing detection approaching detection bill remaining detection (1) bill remaining detection (2) bill remaining detection (1) bill remaining detection (2) bill remaining detection (1) bill remaining detection (2) bill remaining detection (1) bill remaining detection (2) BV unit of verification block



HL2 : half-locked fitness unit of verification block



PSD10L PSD10R PSD11L PSD11R



: : : :



RJ1 RJ1 RJ2 RJ2



bill bill bill bill



remaining remaining remaining remaining



of of of of



inlet inlet inlet inlet



(L) (R) (L) (R)



on reset begin process after changing process mode in aging



Method of check



Measures



dirt sensor, flawing, adhesion of foreign matter



Visually check around sensor



Clean sensor or replace Remove foreign matter Correct to set or replace sensor



gap optical axis



Visually check to state of setting sensor and bracket deformation Visually check around sensor



replace bracket Check guide plate and belt



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



sensor level error



Check to display sensor level(RAS)



Clean sensor



sensor defection



Check to “PORT READ”(RAS) Check port which change sensor status



Adjust sensor or replace



deformation of guide plate come off belt、expand come off connector breaking of wire



Replace verification unit defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Resume process Open unit of error cause and close it. After it, press CLEAR key.



ERROR TYPE



jam：rotate detection error(rotate error, lock error) Abstruct



Check timing



It isn’t achievement to normal revolution cycle at boot. It becomes out of normal revolution cycle.



Code, Sensor name, Content 2901 2905 2906



MDCD01,MD1_CNT : rotate error of RJ transfer motor



MDCE01,ME1_CNT transfer motor MDCE02,ME2_CNT transfer motor



: rotate error of intermediate (1) : rotate error of intermediate (2)



start to move motor and rotating motor



Error cause



Method of check



Measures



gap actuator, adjust defection into foreign matter



Visually check actuator



Adjust actuator Remove foreign matter



come off connector breaking of wire



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



actuator defection slip timing belt, adjust defection



Check to “DRIVE CHECK”(RAS)



Replace actuator Adjust timing belt or replace



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board)



Resume process Open unit of error cause and close it. After it, press CLEAR key.



ERROR TYPE



jam：rotate detection error(rotate error, lock error) Abstruct



Check timing



Motor locks after normal revolution.



Code, Sensor name, Content 2907 2911 2912



MDCD01,MDCD01LD : lock motor of RJ transfer



MDCE01,MDDE01LD : lock motor of intermediate transfer (1) MDCE02,MDCE02LD : lock motor of intermediate transfer (2)



start to move motor and rotating motor



Error cause



Method of check



Measures



gap actuator, adjust defection into foreign matter



Visually check actuator



Adjust actuator Remove foreign matter



come off connector breaking of wire



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



actuator defection slip timing belt, adjust defection



Check to “DRIVE CHECK”(RAS)



Replace actuator Adjust timing belt or replace



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board)



Resume process Open unit of error cause and close it. After it, press CLEAR key.



ERROR TYPE



jam：rotate detection error(rotate error, lock error) Abstruct



Check timing



Feeding motor becomes abnormal revolution.



Code, Sensor name, Content 2913



SMB01 : rotate error of feeding motor



rotating motor



Error cause



Method of check



Measures



gap actuator, adjust defection into foreign matter



Visually check actuator



Adjust actuator Remove foreign matter



interrupter defection



Visually check state of interruptor Check to “PORT READ”(RAS) Check port which change sensor status



Correct to set or replace interruptor



come off connector breaking of wire



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



actuator defection slip timing belt, adjust defection



Check to “DRIVE CHECK”(RAS)



Replace actuator Adjust timing belt or replace



defection of electric board (MAINCPU board) (I/O-CORE board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (I/O-CORE board)



Resume process Open unit of error cause and close it. After it, press CLEAR key.



ERROR TYPE



jam：rotate detection error(rotate error, lock error) Abstruct



Check timing



Stacker fan motor becomes abnormal revolution.



Code, Sensor name, Content 2914 2915 2916 2917 2918 2919 2920 2921 2922 2923



SMD01,PID01 : rotate error of RJ1 fan motor SMD02,PID03 : rotate error of RJ2 fan motor SME01,PIE01 : rotate error of stacker1 fan motor SME02,PIE03 : rotate error of stacker2 fan motor SME03,PIE05 : rotate error of stacker3 fan motor SME04,PIE07 : rotate error of stacker4 fan motor SME05,PIE11 : rotate error of stacker5 fan motor SME06,PIE13 : rotate error of stacker6 fan motor SME07,PIE15 : rotate error of stacker7 fan motor SME08,PIE17 : rotate error of stacker8 fan motor



rotating motor



Error cause



Method of check



Measures



gap actuator, adjust defection into foreign matter



Visually check actuator



Adjust actuator Remove foreign matter



interrupter defection



Visually check state of interruptor Check to “PORT READ”(RAS) Check port which change sensor status



Correct to set or replace interruptor



come off connector breaking of wire



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



actuator defection slip timing belt, adjust defection



Check to “DRIVE CHECK”(RAS)



Replace actuator Adjust timing belt or replace



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board)



Resume process Open unit of error cause and close it. After it, press CLEAR key.



ERROR TYPE



bill remaining error：bill remaining error Abstruct



Check timing



Sensor detects remaining bill or other matter.



on reset end of counting



Code, Sensor name, Content 3001 3002 3003 3006 3007 3008 3009 3010 3011 3012 3013 3014 3015 3017 3018 3019 3021 3022 3023 3026 3028 3029 3031 3032 3034 3035 3037 3044 3046 3047 3049 3050 3052 3053 3055



PSB01L : skew detection (L) PSB01C : skew detection (C) PSB01R : skew detection (R) PSB03L : begin to trace (L) PSB03R : begin to trace (R) VP1L : pass detection of verification block VP1R : pass detection of verification block VP3L : pass detection of verification block VP3R : pass detection of verification block PSD01L : BVREQ timing detection (L) PSD01R : BVREQ timing detection (R) PSD02L : RJ1 branch timing detection (L) PSD02R : RJ1 branch timing detection (R) PSD03 : RJ1 approaching detection PSD05L : RJ2 branch timing detection (L) PSD05R : RJ2 branch timing detection (R) PSD06 : RJ2 approaching detection PSD08 : check branch of transfer PSD09 : pass detection of joint part PSE01 : stacker1 branch timing detection PSE02 : stacker1 approaching detection PSE03 : stacker2 branch timing detection PSE04 : stacker2 approaching detection PSE05 : stacker3 branch timing detection PSE06 : stacker3 approaching detection PSE07 : stacker4 branch timing detection PSE08 : stacker4 approaching detection PSE17 : stacker5 branch timing detection PSE18 : stacker5 approaching detection PSE19 : stacker6 branch timing detection PSE20 : stacker6 approaching detection PSE21 : stacker7 branch timing detection PSE22 : stacker7 approaching detection PSE23 : stacker8 branch timing detection PSE24 : stacker8 approaching detection



Error cause



(1L) (1R) (2L) (2R)



Method of check



Measures



dirt sensor, flawing, adhesion of foreign matter



Visually check around sensor



Clean sensor or replace Remove foreign matter Correct to set or replace sensor



gap optical axis



Visually check to state of setting sensor and bracket deformation Visually check around sensor



replace bracket Check guide plate and belt



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



sensor level error



Check to display sensor level(RAS)



Clean sensor



sensor defection



Check to “PORT READ”(RAS) Check port which change sensor status



Adjust sensor or replace



deformation of guide plate come off belt、expand come off connector breaking of wire



Replace verification unit defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Resume process Open unit of error cause and close it. After it, press CLEAR key.



ERROR TYPE



bill remaining error：bill remaining error Abstruct



Check timing



Sensor detects remaining bill or other matter.



Code, Sensor name, Content 3079 3080 3081 3082



PSD10L PSD10R PSD11L PSD11R



: : : :



RJ1 RJ1 RJ2 RJ2



bill bill bill bill



remaining remaining remaining remaining



on reset end of counting



Error cause of of of of



inlet inlet inlet inlet



(L) (R) (L) (R)



Method of check



Measures



dirt sensor, flawing, adhesion of foreign matter



Visually check around sensor



Clean sensor or replace Remove foreign matter Correct to set or replace sensor



gap optical axis



Visually check to state of setting sensor and bracket deformation Visually check around sensor



replace bracket Check guide plate and belt



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



sensor level error



Check to display sensor level(RAS)



Clean sensor



sensor defection



Check to “PORT READ”(RAS) Check port which change sensor status



Adjust sensor or replace



deformation of guide plate come off belt、expand come off connector breaking of wire



Replace verification unit defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Resume process Open unit of error cause and close it. After it, press CLEAR key.



ERROR TYPE



jam：jam (in the section) Abstruct



Check timing



Over time or over approaching feeding bills in the section below.



Code, Sensor name, Content 3201 3202 3203 3204 3205 3206 3207 3208 3209 3210 3211 3212 3213 3214 3215 3216 3217



PSB03～VP3 : from begin to trace to pass detection of verification block (2) VP3～PSD02 : from pass detection of verification block (2) to RJ1 branch timing detection PSD02～PSD05 : from RJ1 branch timing detection to RJ2 branch timing detection PSD02～PSD03 : from RJ1 branch timing detection to RJ1 approaching detection PSD05～PSD08 : from RJ2 branch timing detection to check branch of transfer PSD05～PSD06 : from RJ2 branch timing detection to RJ2 approaching detection PSD08～PSD09 : from check branch of transfer to pass detection of joint part PSD09～PSE01 : from pass detection of joint part to stacker1 branch timing detection PSE01～PSE02 : from stacker1 branch timing detection to stacker1 approaching detection PSE01～PSE03 : from stacker1 branch timing detection to stacker2 branch timing detection PSE03～PSE04 : from stacker2 branch timing detection to stacker2 approaching detection PSE03～PSE05 : from stacker2 branch timing detection to stacker3 branch timing detection PSE05～PSE06 : from stacker3 branch timing detection to stacker3 approaching detection PSE05～PSE07 : from stacker3 branch timing detection to stacker4 branch timing detection PSE07～PSE08 : from stacker4 branch timing detection to stacker4 approaching detection PSE07～PSE17 : from stacker4 branch timing detection to stacker5 branch timing detection PSE17～PSE18 : from stacker5 branch timing detection to stacker5 approaching detection



feeding bills（include on reset and except in slow feeding）



Error cause



Method of check



Measures



abnormal bills



Visually check the bills



Remove abnormal bills



dirt sensor, flawing, adhesion of foreign matter



Visually check around sensor



Clean sensor or replace Remove foreign matter Correct to set or replace sensor



gap optical axis



Visually check to state of setting sensor and bracket deformation Visually check around sensor



replace bracket Check guide plate and belt



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



sensor level error



Check to display sensor level(RAS)



Clean sensor



sensor defection



Check to “PORT READ”(RAS) Check port which change sensor status



Adjust sensor or replace Replace verification unit



feed gate defection



Check to “REJECT COUNT”（RAS）



adjust feed gate



flipping defection



Check moving (RAS)



replace solenoid adjust or replace flipper



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



deformation of guide plate come off belt、expand come off connector breaking of wire



Resume process Open unit of error cause and close it. After it, press CLEAR key.



ERROR TYPE



jam：jam (in the section) Abstruct



Check timing



Over time or over approaching feeding bills in the section below.



Code, Sensor name, Content 3218 3219 3220 3221 3222 3223



PSE17～PSE19 detection to PSE19～PSE20 detection to PSE19～PSE21 detection to PSE21～PSE22 detection to PSE21～PSE23 detection to PSE23～PSE24 detection to



: from stacker5 branch timing stacker6 branch timing detection : from stacker6 branch timing stacker6 approaching detection : from stacker6 branch timing stacker7 branch timing detection : from stacker7 branch timing stacker7 approaching detection : from stacker7 branch timing stacker8 branch timing detection : from stacker8 branch timing stacker8 approaching detection



feeding bills（include on reset and except in slow feeding）



Error cause



Method of check



Measures



abnormal bills



Visually check the bills



Remove abnormal bills



dirt sensor, flawing, adhesion of foreign matter



Visually check around sensor



Clean sensor or replace Remove foreign matter Correct to set or replace sensor



gap optical axis



Visually check to state of setting sensor and bracket deformation Visually check around sensor



Replace bracket Check guide plate and belt



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



sensor level error



Check to display sensor level(RAS)



Clean sensor



sensor defection



Check to “PORT READ”(RAS) Check port which change sensor status



Adjust sensor or replace Replace verification unit



feed gate defection



Check to “REJECT COUNT”（RAS）



Adjust feed gate



flipping defection



Check moving (RAS)



replace solenoid adjust or replace flipper



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



deformation of guide plate come off belt、expand come off connector breaking of wire



Resume process Open unit of error cause and close it. After it, press CLEAR key.



ERROR TYPE



jam：jam (bill detection before feeding) Abstruct



Check timing



Interrupt sensor even it isn’t feed bills.



Code, Sensor name, Content 3301 3302 3303 3304 3305 3306 3307 3308 3309 3310 3311 3312 3313 3314 3315 3316 3317 3318 3319 3320 3321 3322 3323 3324



VP3 : PSD01 PSD02 PSD03 PSD05 PSD06 PSD08 PSD09 PSE01 PSE02 PSE03 PSE04 PSE05 PSE06 PSE07 PSE08 PSE17 PSE18 PSE19 PSE20 PSE21 PSE22 PSE23 PSE24



pass detection of verification block : BVREQ timing detection : RJ1 branch timing detection : RJ1 approaching detection : RJ2 branch timing detection : RJ2 approaching detection : check branch of transfer : pass detection of joint part : stacker1 branch timing detection : stacker1 approaching detection : stacker2 branch timing detection : stacker2 approaching detection : stacker3 branch timing detection : stacker3 approaching detection : stacker4 branch timing detection : stacker4 approaching detection : stacker5 branch timing detection : stacker5 approaching detection : stacker6 branch timing detection : stacker6 approaching detection : stacker7 branch timing detection : stacker7 approaching detection : stacker8 branch timing detection : stacker8 approaching detection



feeding bills except reset



Error cause



Method of check



Measures



dirt sensor, flawing, adhesion of foreign matter



Visually check around sensor



Clean sensor or replace Remove foreign matter Correct to set or replace sensor



gap optical axis



Visually check to state of setting sensor and bracket deformation Visually check around sensor



Replace bracket Check guide plate and belt



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



sensor level error



Check to display sensor level(RAS)



Clean sensor



sensor defection



Check to “PORT READ”(RAS) Check port which change sensor status



Adjust sensor or replace



deformation of guide plate come off belt、expand come off connector breaking of wire



Replace verification unit defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Resume process Open unit of error cause and close it. After it, press CLEAR key.



ERROR TYPE



jam：jam (feed block) Abstruct



Check timing



Detect accumlation bills or foreign matter at feed block.



Code, Sensor name, Content 3326



PSB01LCR :jam on feed



rotating motor



Error cause



Method of check



Measures



abnormal bills



Visually check the bills



Remove abnormal bills



dirt sensor, flawing, adhesion of foreign matter



Visually check around sensor



Clean sensor or replace Remove foreign matter Correct to set or replace sensor



gap optical axis



Visually check to state of setting sensor and bracket deformation Visually check around sensor



replace bracket Check guide plate and belt



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



sensor level error



Check to display sensor level(RAS)



Clean sensor



sensor defection



Check to “PORT READ”(RAS) Check port which change sensor status



Adjust sensor or replace



deformation of guide plate come off belt、expand come off connector breaking of wire



Replace verification unit feed gate defection



Check to “REJECT COUNT”（RAS）



Adjust feed gate



defection of electric board (MAINCPU board) (I/O-CORE board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (I/O-CORE board)



Resume process Open unit of error cause and close it. After it, press CLEAR key.



ERROR TYPE



set defection：set defection Abstruct



Check timing



Detect set SW to off.



in processing in aging



Code, Sensor name, Content 4002 4004 4005 4006



SWZ02 SWZ04 SWE01 SWE02



: : : :



set set set set



SW SW SW SW



of of of of



RJ transportation front cover intermediate transportation 1 intermediate transportation 2



Error cause



Method of check



Measures



open the unit



Check switch and detecting plate



Set unit Adjust placement or replace



come off connector breaking of wire



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



switch defection



Check to “PORT READ”(RAS) Check port which change sensor status



Replace switch



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board)



Resume process Set unit of error cause. After it, press CLEAR key.



ERROR TYPE



feeding trouble：transfer failure (accumulation, defect bills) Abstruct



Check timing



Detect accumulation or defect bills.



Code, Sensor name, Content 5001 5002 5003 5004 5005 5006 5007 5008 5009 5010 5011 5012 5013 5014 5015 5016 5017 5018 5019 5020 5021



PSD02 PSD05 PSD06 PSD08 PSD09 PSE01 PSE02 PSE03 PSE04 PSE05 PSE06 PSE07 PSE08 PSE17 PSE18 PSE19 PSE20 PSE21 PSE22 PSE23 PSE24



: : : : : : : : : : : : : : : : : : : : :



RJ1 branch timing detection RJ2 branch timing detection RJ2 approaching detection check branch of transfer pass detection of joint part stacker1 branch timing detection stacker1 approaching detection stacker2 branch timing detection stacker2 approaching detection stacker3 branch timing detection stacker3 approaching detection stacker4 branch timing detection stacker4 approaching detection stacker5 branch timing detection stacker5 approaching detection stacker6 branch timing detection stacker6 approaching detection stacker7 branch timing detection stacker7 approaching detection stacker8 branch timing detection stacker8 approaching detection



feeding bills except reset



Error cause



Method of check



Measures



abnormal bills



Visually check the bills



Remove abnormal bills



dirt sensor, flawing, adhesion of foreign matter



Visually check around sensor



Clean sensor or replace Remove foreign matter Correct to set or replace sensor



gap optical axis



Visually check to state of setting sensor and bracket deformation Visually check around sensor



replace bracket Check guide plate and belt



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



sensor level error



Check to display sensor level(RAS)



Clean sensor



sensor defection



Check to “PORT READ”(RAS) Check port which change sensor status



Adjust sensor or replace Replace verification unit



feed gate defection



Check to “REJECT COUNT”（RAS）



adjust feed gate



flipping defection



Check moving (RAS)



replace solenoid adjust or replace flipper



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



deformation of guide plate come off belt、expand come off connector breaking of wire



Resume process Press CLEAR key.



ERROR TYPE



feeding trouble：transfer failure (short pitch of feeding bills) Abstruct



Check timing



Detect abnormal pitch of feeding bills.



Code, Sensor name, Content 5050 5051 5052 5053 5054 5055 5056 5057 5058 5059 5060 5061 5062 5063 5064 5065 5066 5067 5068 5069 5070



PSD02 PSD05 PSD06 PSD08 PSD09 PSE01 PSE02 PSE03 PSE04 PSE05 PSE06 PSE07 PSE08 PSE17 PSE18 PSE19 PSE20 PSE21 PSE22 PSE23 PSE24



: : : : : : : : : : : : : : : : : : : : :



RJ1 branch timing detection RJ2 branch timing detection RJ2 approaching detection check branch of transfer pass detection of joint part stacker1 branch timing detection stacker1 approaching detection stacker2 branch timing detection stacker2 approaching detection stacker3 branch timing detection stacker3 approaching detection stacker4 branch timing detection stacker4 approaching detection stacker5 branch timing detection stacker5 approaching detection stacker6 branch timing detection stacker6 approaching detection stacker7 branch timing detection stacker7 approaching detection stacker8 branch timing detection stacker8 approaching detection



feeding bills except reset



Error cause



Method of check



Measures



abnormal bills



Visually check the bills



Remove abnormal bills



dirt sensor, flawing, adhesion of foreign matter



Visually check around sensor



Clean sensor or replace Remove foreign matter Correct to set or replace sensor



gap optical axis



Visually check to state of setting sensor and bracket deformation Visually check around sensor



replace bracket Check guide plate and belt



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



sensor level error



Check to display sensor level(RAS)



Clean sensor



sensor defection



Check to “PORT READ”(RAS) Check port which change sensor status



Adjust sensor or replace Replace verification unit



flipping defection



Check moving (RAS)



replace solenoid adjust or replace flipper



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



deformation of guide plate come off belt、expand come off connector breaking of wire



Resume process Press CLEAR key.



ERROR TYPE



feeding trouble：transfer failure (transfer gap) Abstruct



Check timing



Detect abnormal transfer gap.



Code, Sensor name, Content 5101 5102 5103 5104 5105 5106 5107 5108 5109 5110 5111 5112 5113 5114 5115 5116 5117



VS01～PSD02 : virtual detection after BVREQ to RJ1 branch timing detection PSD02～PSD05 : from RJ1 branch timing detection to RJ2 branch timing detection PSD05～PSD08 : from RJ2 branch timing detection to check branch of transfer PSD05～PSD06 : from RJ2 branch timing detection to RJ2 approaching detection PSD08～PSD09 : from check branch of transfer to pass detection of joint part PSD09～PSE01 : from pass detection of joint part to stacker1 branch timing detection PSE01～PSE02 : from stacker1 branch timing detection to stacker1 approaching detection PSE01～PSE03 : from stacker1 branch timing detection to stacker2 branch timing detection PSE03～PSE04 : from stacker2 branch timing detection to stacker2 approaching detection PSE03～PSE05 : from stacker2 branch timing detection to stacker3 branch timing detection PSE05～PSE06 : from stacker3 branch timing detection to stacker3 approaching detection PSE05～PSE07 : from stacker3 branch timing detection to stacker4 branch timing detection PSE07～PSE08 : from stacker4 branch timing detection to stacker4 approaching detection PSE07～PSE17 : from stacker4 branch timing detection to stacker5 branch timing detection PSE17～PSE18 : from stacker5 branch timing detection to stacker5 approaching detection PSE17～PSE19 : from stacker5 branch timing detection to stacker6 branch timing detection PSE19～PSE20 : from stacker6 branch timing detection to stacker6 approaching detection



feeding bills except reset



Error cause



Method of check



Measures



abnormal bills



Visually check the bills



Remove abnormal bills



dirt sensor, flawing, adhesion of foreign matter



Visually check around sensor



Clean sensor or replace Remove foreign matter Correct to set or replace sensor



gap optical axis



Visually check to state of setting sensor and bracket deformation Visually check around sensor



replace bracket Check guide plate and belt



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



sensor level error



Check to display sensor level(RAS)



Clean sensor



sensor defection



Check to “PORT READ”(RAS) Check port which change sensor status



Adjust sensor or replace Replace verification unit



flipping defection



Check moving (RAS)



replace solenoid adjust or replace flipper



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



deformation of guide plate come off belt、expand come off connector breaking of wire



Resume process Press CLEAR key.



ERROR TYPE



feeding trouble：transfer failure (transfer gap) Abstruct



Check timing



Detect abnormal transfer gap.



Code, Sensor name, Content 5118 5119 5120 5121



PSE19～PSE21 detection to PSE21～PSE22 detection to PSE21～PSE23 detection to PSE23～PSE24 detection to



: from stacker6 branch timing stacker7 branch timing detection : from stacker7 branch timing stacker7 approaching detection : from stacker7 branch timing stacker8 branch timing detection : from stacker8 branch timing stacker8 approaching detection



feeding bills except reset



Error cause



Method of check



Measures



abnormal bills



Visually check the bills



Remove abnormal bills



dirt sensor, flawing, adhesion of foreign matter



Visually check around sensor



Clean sensor or replace Remove foreign matter Correct to set or replace sensor



gap optical axis



Visually check to state of setting sensor and bracket deformation Visually check around sensor



replace bracket Check guide plate and belt



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



sensor level error



Check to display sensor level(RAS)



Clean sensor



sensor defection



Check to “PORT READ”(RAS) Check port which change sensor status



Adjust sensor or replace Replace verification unit



flipping defection



Check moving (RAS)



replace solenoid adjust or replace flipper



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



deformation of guide plate come off belt、expand come off connector breaking of wire



Resume process Press CLEAR key.



ERROR TYPE



feeding trouble：transfer failure (reject bills accumulation) Abstruct



Check timing



Detect to accumlate reject bills.



Code, Sensor name, Content 5155



PSD02～PSD05 : from RJ1 branch timing detection to RJ2 branch timing detection



feeding bills except reset



Error cause



Method of check



Measures



abnormal bills



Visually check the bills



Remove abnormal bills



dirt sensor, flawing, adhesion of foreign matter



Visually check around sensor



Clean sensor or replace Remove foreign matter Correct to set or replace sensor



gap optical axis



Visually check to state of setting sensor and bracket deformation Visually check around sensor



replace bracket Check guide plate and belt



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



sensor level error



Check to display sensor level(RAS)



Clean sensor



sensor defection



Check to “PORT READ”(RAS) Check port which change sensor status



Adjust sensor or replace Replace verification unit



flipping defection



Check moving (RAS)



replace solenoid adjust or replace flipper



defection of electric board (MAINCPU board) (I/O-CORE board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (I/O-CORE board)



deformation of guide plate come off belt、expand come off connector breaking of wire



Resume process Press CLEAR key.



ERROR TYPE



feeding trouble：transfer failure (chain bills accumulation) Abstruct



Check timing



Detect to accumlate chain bills.



Code, Sensor name, Content 5160



PSD02～PSD05 : from RJ1 branch timing detection to RJ2 branch timing detection



feeding bills except reset



Error cause



Method of check



Measures



abnormal bills



Visually check the bills



Remove abnormal bills



dirt sensor, flawing, adhesion of foreign matter



Visually check around sensor



Clean sensor or replace Remove foreign matter Correct to set or replace sensor



gap optical axis



Visually check to state of setting sensor and bracket deformation Visually check around sensor



replace bracket Check guide plate and belt



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



sensor level error



Check to display sensor level(RAS)



Clean sensor



sensor defection



Check to “PORT READ”(RAS) Check port which change sensor status



Adjust sensor or replace



flipping defection



Check moving (RAS)



replace solenoid adjust or replace flipper



defection of electric board (MAINCPU board) (I/O-CORE board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (I/O-CORE board)



deformation of guide plate come off belt、expand come off connector breaking of wire



Resume process Press CLEAR key.



ERROR TYPE



feeding trouble：counter unmatch (sensor pass counter overflow) Abstruct



Check timing



Detect counter overflow.



Code, Sensor name, Content 5201



count/transaction pass counter2 count/transaction end of tracing pass counter2



on counting (interrupt sensor)



Error cause defection of electric board (MAINCPU board) (verification board)



Method of check Check reset machine and do initialize



software defection



ERROR TYPE



Replace electric board (MAINCPU board) (verification board)



feeding trouble：counter unmatch (reject counter for normal bills overflow) Abstruct



Code, Sensor name, Content counter of reject normal bills



Resume process Press CLEAR key.



version up software



Check timing



Detect counter overflow.



5202



Measures



on counting (verification)



Error cause defection of electric board (MAINCPU board) (verification board) software defection



Method of check Check reset machine and do initialize



Measures Replace electric board (MAINCPU board) (verification board) version up software



Resume process Press CLEAR key.



ERROR TYPE



feeding trouble：counter unmatch (counter overflow) Abstruct



Check timing



Detect counter overflow.



Code, Sensor name, Content 5203 5204



counting counter2 transaction counter2



on counting



Error cause defection of electric board (MAINCPU board) (verification board)



Method of check Check reset machine and do initialize



software defection



ERROR TYPE



Replace electric board (MAINCPU board) (verification board)



feeding trouble：counter unmatch (direction counter overflow) Abstruct



Code, Sensor name, Content counting counter2 for each directions transaction counter2 for each directions



Resume process Press CLEAR key.



version up software



Check timing



Detect counter overflow.



5209 5210



Measures



on counting



Error cause defection of electric board (MAINCPU board) (verification board) software defection



Method of check Check reset machine and do initialize



Measures Replace electric board (MAINCPU board) (verification board) version up software



Resume process Press CLEAR key.



ERROR TYPE



feeding trouble：feed error (feeding time error) Abstruct



Check timing



Detect error of feeding time.



Code, Sensor name, Content 5301 5302 5303 5304 5305 5306 5307 5308 5309 5310 5311 5312 5313 5314 5315 5316 5317



VS01～PSD02 : virtual detection after BVREQ to RJ1 branch timing detection PSD02～PSD05 : from RJ1 branch timing detection to RJ2 branch timing detection PSD05～PSD08 : from RJ2 branch timing detection to check branch of transfer PSD05～PSD06 : from RJ2 branch timing detection to RJ2 approaching detection PSD08～PSD09 : from check branch of transfer to pass detection of joint part PSD09～PSE01 : from pass detection of joint part to stacker1 branch timing detection PSE01～PSE02 : from stacker1 branch timing detection to stacker1 approaching detection PSE01～PSE03 : from stacker1 branch timing detection to stacker2 branch timing detection PSE03～PSE04 : from stacker2 branch timing detection to stacker2 approaching detection PSE03～PSE05 : from stacker2 branch timing detection to stacker3 branch timing detection PSE05～PSE06 : from stacker3 branch timing detection to stacker3 approaching detection PSE05～PSE07 : from stacker3 branch timing detection to stacker4 branch timing detection PSE07～PSE08 : from stacker4 branch timing detection to stacker4 approaching detection PSE07～PSE17 : from stacker4 branch timing detection to stacker5 branch timing detection PSE17～PSE18 : from stacker5 branch timing detection to stacker5 approaching detection PSE17～PSE19 : from stacker5 branch timing detection to stacker6 branch timing detection PSE19～PSE20 : from stacker6 branch timing detection to stacker6 approaching detection



feeding bills except reset



Error cause



Method of check



Measures



abnormal bills



Visually check the bills



Remove abnormal bills



dirt sensor, flawing, adhesion of foreign matter



Visually check around sensor



Clean sensor or replace Remove foreign matter Correct to set or replace sensor



gap optical axis



Visually check to state of setting sensor and bracket deformation Visually check around sensor



replace bracket Check guide plate and belt



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



sensor level error



Check to display sensor level(RAS)



Clean sensor



sensor defection



Check to “PORT READ”(RAS) Check port which change sensor status



Adjust sensor or replace Replace verification unit



flipping defection



Check moving (RAS)



replace solenoid adjust or replace flipper



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



deformation of guide plate come off belt、expand come off connector breaking of wire



Resume process Press CLEAR key.



ERROR TYPE



feeding trouble：feed error (feeding time error) Abstruct



Check timing



Detect error of feeding time.



Code, Sensor name, Content 5318 5319 5320 5321



PSE19～PSE21 detection to PSE21～PSE22 detection to PSE21～PSE23 detection to PSE23～PSE24 detection to



: from stacker6 branch timing stacker7 branch timing detection : from stacker7 branch timing stacker7 approaching detection : from stacker7 branch timing stacker8 branch timing detection : from stacker8 branch timing stacker8 approaching detection



feeding bills except reset



Error cause



Method of check



Measures



abnormal bills



Visually check the bills



Remove abnormal bills



dirt sensor, flawing, adhesion of foreign matter



Visually check around sensor



Clean sensor or replace Remove foreign matter Correct to set or replace sensor



gap optical axis



Visually check to state of setting sensor and bracket deformation Visually check around sensor



replace bracket Check guide plate and belt



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



sensor level error



Check to display sensor level(RAS)



Clean sensor



sensor defection



Check to “PORT READ”(RAS) Check port which change sensor status



Adjust sensor or replace Replace verification unit



flipping defection



Check moving (RAS)



replace solenoid adjust or replace flipper



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



deformation of guide plate come off belt、expand come off connector breaking of wire



Resume process Press CLEAR key.



ERROR TYPE



feeding trouble：feed error (trace data error) Abstruct



Check timing



Detect error of trace data.



Code, Sensor name, Content 5350 5351 5352 5353 5354 5355 5356 5357 5358 5359 5360 5361 5362 5363 5364 5365 5366 5367 5368 5369 5370 5371 5372



VS01 : virtual detection after BVREQ PSD02 : RJ1 branch timing detection PSD03 : RJ1 approaching detection PSD05 : RJ2 branch timing detection PSD06 : RJ2 approaching detection PSD08 : check branch of transfer PSD09 : pass detection of joint part PSE01 : stacker1 branch timing detection PSE02 : stacker1 approaching detection PSE03 : stacker2 branch timing detection PSE04 : stacker2 approaching detection PSE05 : stacker3 branch timing detection PSE06 : stacker3 approaching detection PSE07 : stacker4 branch timing detection PSE08 : stacker4 approaching detection PSE17 : stacker5 branch timing detection PSE18 : stacker5 approaching detection PSE19 : stacker6 branch timing detection PSE20 : stacker6 approaching detection PSE21 : stacker7 branch timing detection PSE22 : stacker7 approaching detection PSE23 : stacker8 branch timing detection PSE24 : stacker8 approaching detection



feeding bills except reset



Error cause



Method of check



Measures



abnormal bills



Visually check the bills



Remove abnormal bills



dirt sensor, flawing, adhesion of foreign matter



Visually check around sensor



Clean sensor or replace Remove foreign matter Correct to set or replace sensor



gap optical axis



Visually check to state of setting sensor and bracket deformation Visually check around sensor



replace bracket Check guide plate and belt



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



sensor level error



Check to display sensor level(RAS)



Clean sensor



sensor defection



Check to “PORT READ”(RAS) Check port which change sensor status



Adjust sensor or replace Replace verification unit



flipping defection



Check moving (RAS)



replace solenoid adjust or replace flipper



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



deformation of guide plate come off belt、expand come off connector breaking of wire



Resume process Press CLEAR key.



ERROR TYPE



feeding trouble：feed error (pass count error) Abstruct



Check timing



Detect pass count error.



Code, Sensor name, Content 5401 5402 5403 5404 5405 5406 5407 5408 5409 5410 5411 5412 5413 5414 5415 5416 5417 5418 5419 5420 5421



PSD02 PSD05 PSD06 PSD08 PSD09 PSE01 PSE02 PSE03 PSE04 PSE05 PSE06 PSE07 PSE08 PSE17 PSE18 PSE19 PSE20 PSE21 PSE22 PSE23 PSE24



: : : : : : : : : : : : : : : : : : : : :



RJ1 branch timing detection RJ2 branch timing detection RJ2 approaching detection check branch of transfer pass detection of joint part stacker1 branch timing detection stacker1 approaching detection stacker2 branch timing detection stacker2 approaching detection stacker3 branch timing detection stacker3 approaching detection stacker4 branch timing detection stacker4 approaching detection stacker5 branch timing detection stacker5 approaching detection stacker6 branch timing detection stacker6 approaching detection stacker7 branch timing detection stacker7 approaching detection stacker8 branch timing detection stacker8 approaching detection



feeding bills except reset



Error cause



Method of check



Measures



abnormal bills



Visually check the bills



Remove abnormal bills



dirt sensor, flawing, adhesion of foreign matter



Visually check around sensor



Clean sensor or replace Remove foreign matter Correct to set or replace sensor



gap optical axis



Visually check to state of setting sensor and bracket deformation Visually check around sensor



replace bracket Check guide plate and belt



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



sensor level error



Check to display sensor level(RAS)



Clean sensor



sensor defection



Check to “PORT READ”(RAS) Check port which change sensor status



Adjust sensor or replace Replace verification unit



flipping defection



Check moving (RAS)



replace solenoid adjust or replace flipper



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



deformation of guide plate come off belt、expand come off connector breaking of wire



Resume process Press CLEAR key.



ERROR TYPE



feeding trouble：feed error (trace data error 2) Abstruct



Check timing



Detect error of trace data.



Code, Sensor name, Content 5450 5451 5452 5453 5454 5455 5456 5457 5458



PSD06 PSE02 PSE04 PSE06 PSE08 PSE18 PSE20 PSE22 PSE24



: : : : : : : : :



RJ2 approaching detection stacker1 approaching detection stacker2 approaching detection stacker3 approaching detection stacker4 approaching detection stacker5 approaching detection stacker6 approaching detection stacker7 approaching detection stacker8 approaching detection



feeding bills except reset



Error cause



Method of check



Measures



abnormal bills



Visually check the bills



Remove abnormal bills



dirt sensor, flawing, adhesion of foreign matter



Visually check around sensor



Clean sensor or replace Remove foreign matter Correct to set or replace sensor



gap optical axis



Visually check to state of setting sensor and bracket deformation Visually check around sensor



replace bracket Check guide plate and belt



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



sensor level error



Check to display sensor level(RAS)



Clean sensor



sensor defection



Check to “PORT READ”(RAS) Check port which change sensor status



Adjust sensor or replace Replace verification unit



flipping defection



Check moving (RAS)



replace solenoid adjust or replace flipper



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



deformation of guide plate come off belt、expand come off connector breaking of wire



Resume process Press CLEAR key.



ERROR TYPE



feeding trouble：feed error (transfer foreign matter) Abstruct



Check timing



Detect transfer foreign matter.



Code, Sensor name, Content 5470



VS01 : virtual detection after BVREQ



feeding bills except reset



Error cause



Method of check



Measures



abnormal bills



Visually check the bills



Remove abnormal bills



dirt sensor, flawing, adhesion of foreign matter



Visually check around sensor



Clean sensor or replace Remove foreign matter Correct to set or replace sensor



gap optical axis



Visually check to state of setting sensor and bracket deformation Visually check around sensor



replace bracket Check guide plate and belt



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



sensor level error



Check to display sensor level(RAS)



Clean sensor



sensor defection



Check to “PORT READ”(RAS) Check port which change sensor status



Adjust sensor or replace Replace verification unit



flipping defection



Check moving (RAS)



replace solenoid adjust or replace flipper



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



deformation of guide plate come off belt、expand come off connector breaking of wire



Resume process Press CLEAR key.



ERROR TYPE



jam：rotate detection error (don’t stop) Abstruct



Check timing



Motor doesn’t stop.



Code, Sensor name, Content 5490 5494 5495



MDCD01,MD1_CNT : don’t stop motor of RJ transfer MDCE01,ME1_CNT : don’t stop motor of intermediate transfer (1) MDCE02,ME2_CNT : don’t stop motor of intermediate transfer (2)



stop motor



Error cause



Method of check



Measures



dirt sensor, flawing, adhesion of foreign matter



Visually check around sensor



Clean sensor or replace Remove foreign matter Correct to set or replace sensor



come off connector breaking of wire



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



actuator defection slip timing belt, adjust defection



Check to “DRIVE CHECK”(RAS)



Replace actuator Adjust timing belt or replace



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board)



Resume process Open unit of error cause and close it. After it, press CLEAR key.



ERROR TYPE



feeding trouble：counting error (pass counter overflow) Abstruct



Check timing



Detect counter overflow.



Code, Sensor name, Content 5501 5502



count pass counter1 count end of tracing pass counter1 transaction pass counter1 transaction end of tracing pass counter1



on counting



Error cause defection of electric board (MAINCPU board) (verification board)



Method of check Check reset machine and do initialize



software defection



ERROR TYPE



Replace electric board (MAINCPU board) (verification board)



feeding trouble：counting error (counter overflow) Abstruct



Code, Sensor name, Content counting counter1 transaction counter1



Resume process Press CLEAR key.



version up software



Check timing



Detect counter overflow.



5503 5504



Measures



on counting



Error cause defection of electric board (MAINCPU board) (verification board) software defection



Method of check Check reset machine and do initialize



Measures Replace electric board (MAINCPU board) (verification board) version up software



Resume process Press CLEAR key.



ERROR TYPE



feeding trouble：counting error (direction counter overflow) Abstruct



Check timing



Detect counter overflow.



Code, Sensor name, Content 5506 5507



counting counter1 for each directions transaction counter1 for each directions



on counting



Error cause defection of electric board (MAINCPU board) (verification board)



Method of check Check reset machine and do initialize



software defection



ERROR TYPE



Replace electric board (MAINCPU board) (verification board)



feeding trouble：counting error (counter unmatch) Abstruct



Code, Sensor name, Content unmatch counting counters unmatch transaction counters



Resume process Press CLEAR key.



version up software



Check timing



Unmatch between counter1 and counter2.



5510 5511



Measures



end of counting start idling



Error cause defection of electric board (MAINCPU board) (verification board) software defection



Method of check Check reset machine and do initialize



Measures Replace electric board (MAINCPU board) (verification board) version up software



Resume process Press CLEAR key.



ERROR TYPE



feeding trouble：counting error (direction counter unmatch) Abstruct



Check timing



Unmatch between counter1 and counter2.



Code, Sensor name, Content 5513



counter for each directions



end of counting start idling



Error cause defection of electric board (MAINCPU board) (verification board)



Method of check Check reset machine and do initialize



software defection



ERROR TYPE



Replace electric board (MAINCPU board) (verification board)



feeding trouble：counting error (unmatch between counters) Abstruct



Code, Sensor name, Content count pass counter1 and count counter1 count pass counter1 and count counter1 for each directions



Resume process Press CLEAR key.



version up software



Check timing



Unmatch to count pass counter1.



5515 5516



Measures



end of counting start idling



Error cause defection of electric board (MAINCPU board) (verification board) software defection



Method of check Check reset machine and do initialize



Measures Replace electric board (MAINCPU board) (verification board) version up software



Resume process Press CLEAR key.



ERROR TYPE



feeding trouble：counting error (verification counter unmatch) Abstruct



Check timing



Unmatch to count counter1.



Code, Sensor name, Content 5517



unmatch verification counter1



end of counting



Error cause defection of electric board (MAINCPU board) (verification board)



Method of check Check reset machine and do initialize



software defection



ERROR TYPE



Measures Replace electric board (MAINCPU board) (verification board)



Press CLEAR key.



version up software



machine trouble：network error Abstruct



Check timing



ARC network error occurs.



Code, Sensor name, Content 5801



Resume process



re-config in processing of MAIN board



in processing



Error cause



Method of check



Measures



come off connector breaking of wire



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



defection of electric board (MAINCPU board)



Check reset machine and do initialize



Replace electric board (MAINCPU board)



Resume process Press CLEAR key.



ERROR TYPE



machine trouble：sensor dust check error Abstruct



Check timing



Transmitter of sensor emits light with half power but can’t detect at receiver.



Code, Sensor name, Content 6001 6002 6003 6004 6007 6008 6009 6011 6012 6013 6014 6015 6016 6017 6018 6023 6024 6025 6026 6027 6028 6029 6030 6031 6032 6033 6034 6035 6036 6037 6038 6039 6040



PSA01 : stack detection of HP PSB01L : skew detection (L) PSB01C : skew detection (C) PSB01R : skew detection (R) PSB03L : begin to trace (L) PSB03R : begin to trace (R) PSB04 : remain detection of HP VP1L : pass detection of verification block (1L) VP1R : pass detection of verification block (1R) VP3L : pass detection of verification block (2L) VP3R : pass detection of verification block (2R) thickness : thickness detection TMP/HUM : temperture / humidity HUM : humidity LS : line sensor TMFL : magnetism sensor (L) TMFR : magnetism sensor (R) UVT : UV sensor FLR : UV sensor LSA : line sensor of verification block (LSA) LSB : line sensor of verification block (LSB) UV : sub sensor of verification block (1UV) FL : sub sensor of verification block (1FL) GSL : sub sensor of verification block (1GSL) GSR : sub sensor of verification block (1GSR) MG : sub sensor of verification block (1MG) TC : sub sensor of verification block (2TC) USR : sub sensor of verification block (2USR) USL : sub sensor of verification block (2USL) PSD01L : BVREQ timing detection (L) PSD01R : BVREQ timing detection (R) PSD02L : RJ1 branch timing detection (L) PSD02R : RJ1 branch timing detection (R)



Error cause



in aging



Method of check



Measures



dirt sensor, flawing, adhesion of foreign matter



Visually check around sensor



Clean sensor or replace Remove foreign matter Correct to set or replace sensor



gap optical axis



Visually check to state of setting sensor and bracket deformation Visually check around sensor



replace bracket Check guide plate and belt



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



sensor level error



Check to display sensor level(RAS)



Clean sensor



sensor defection



Check to “PORT READ”(RAS) Check port which change sensor status



Adjust sensor or replace



deformation of guide plate come off belt、expand come off connector breaking of wire



Replace verification unit defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Resume process Press CLEAR key.



ERROR TYPE



machine trouble：sensor dust check error Abstruct



Check timing



Transmitter of sensor emits light with half power but can’t detect at receiver.



Code, Sensor name, Content 6042 6043 6044 6045 6046 6048 6049 6050 6051 6052 6055 6057 6058 6060 6061 6063 6064 6066 6067 6068 6069 6070 6071 6072 6073 6074 6081 6083 6084 6086 6087 6089 6090 6092



PSD03 : RJ1 approaching detection PSD04L : RJ1 bill remaining detection (L) PSD04R : RJ1 bill remaining detection (R) PSD05L : RJ2 branch timing detection (L) PSD05R : RJ2 branch timing detection (R) PSD06 : RJ2 approaching detection PSD07L : RJ2 bill remaining (L) PSD07R : RJ2 bill remaining (R) PSD08 : check branch of transfer PSD09 : pass detection of joint part PSE01 : stacker1 branch timing detection PSE02 : stacker1 approaching detection PSE03 : stacker2 branch timing detection PSE04 : stacker2 approaching detection PSE05 : stacker3 branch timing detection PSE06 : stacker3 approaching detection PSE07 : stacker4 branch timing detection PSE08 : stacker4 approaching detection PSE09 : stacker1 bill remaining detection PSE10 : stacker1 bill remaining detection PSE11 : stacker2 bill remaining detection PSE12 : stacker2 bill remaining detection PSE13 : stacker3 bill remaining detection PSE14 : stacker3 bill remaining detection PSE15 : stacker4 bill remaining detection PSE16 : stacker4 bill remaining detection PSE17 : stacker5 branch timing detection PSE18 : stacker5 approaching detection PSE19 : stacker6 branch timing detection PSE20 : stacker6 approaching detection PSE21 : stacker7 branch timing detection PSE22 : stacker7 approaching detection PSE23 : stacker8 branch timing detection PSE24 : stacker8 approaching detection



Error cause



in aging



Method of check



Measures



dirt sensor, flawing, adhesion of foreign matter



Visually check around sensor



Clean sensor or replace Remove foreign matter Correct to set or replace sensor



gap optical axis



Visually check to state of setting sensor and bracket deformation Visually check around sensor



replace bracket Check guide plate and belt



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



sensor level error



Check to display sensor level(RAS)



Clean sensor



sensor defection



Check to “PORT READ”(RAS) Check port which change sensor status



Adjust sensor or replace



deformation of guide plate come off belt、expand come off connector breaking of wire



Replace verification unit



(1) (2) (1) (2) (1) (2) (1) (2)



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Resume process Press CLEAR key.



ERROR TYPE



machine trouble：sensor dust check error Abstruct



Check timing



Transmitter of sensor emits light with half power but can’t detect at receiver.



Code, Sensor name, Content 6093 6094 6095 6096 6097 6098 6099 6100 6124 6125 6126 6127



PSE25 : stacker5 bill remaining detection PSE26 : stacker5 bill remaining detection PSE27 : stacker6 bill remaining detection PSE28 : stacker6 bill remaining detection PSE29 : stacker7 bill remaining detection PSE30 : stacker7 bill remaining detection PSE31 : stacker8 bill remaining detection PSE32 : stacker8 bill remaining detection PSD10L : RJ1 bill remaining of inlet (L) PSD10R : RJ1 bill remaining of inlet (R) PSD11L : RJ2 bill remaining of inlet (L) PSD11R : RJ2 bill remaining of inlet (R)



Error cause (1) (2) (1) (2) (1) (2) (1) (2)



in aging



Method of check



Measures



dirt sensor, flawing, adhesion of foreign matter



Visually check around sensor



Clean sensor or replace Remove foreign matter Correct to set or replace sensor



gap optical axis



Visually check to state of setting sensor and bracket deformation Visually check around sensor



replace bracket Check guide plate and belt



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



sensor level error



Check to display sensor level(RAS)



Clean sensor



sensor defection



Check to “PORT READ”(RAS) Check port which change sensor status



Adjust sensor or replace



deformation of guide plate come off belt、expand come off connector breaking of wire



Replace verification unit defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Resume process Press CLEAR key.



ERROR TYPE



machine trouble：sensor OFF check error Abstruct



Check timing



Transmitter of sensor stops to emit light but detect light at receiver.



Code, Sensor name, Content 7001 7002 7003 7004 7007 7008 7009 7011 7012 7013 7014 7037 7038 7039 7040 7042 7043 7044 7045 7046 7048 7049 7050 7051 7052 7055 7057 7058 7060 7061 7063 7064 7066



PSA01 : stack detection of HP PSB01L : skew detection (L) PSB01C : skew detection (C) PSB01R : skew detection (R) PSB03L : begin to trace (L) PSB03R : begin to trace (R) PSB04 : remain detection of HP VP1L : pass detection of verification block (1L) VP1R : pass detection of verification block (1R) VP3L : pass detection of verification block (2L) VP3R : pass detection of verification block (2R) PSD01L : BVREQ timing detection (L) PSD01R : BVREQ timing detection (R) PSD02L : RJ1 branch timing detection (L) PSD02R : RJ1 branch timing detection (R) PSD03 : RJ1 approaching detection PSD04L : RJ1 bill remaining detection (L) PSD04R : RJ1 bill remaining detection (R) PSD05L : RJ2 branch timing detection (L) PSD05R : RJ2 branch timing detection (R) PSD06 : RJ2 approaching detection PSD07L : RJ2 bill remaining (L) PSD07R : RJ2 bill remaining (R) PSD08 : check branch of transfer PSD09 : pass detection of joint part PSE01 : stacker1 branch timing detection PSE02 : stacker1 approaching detection PSE03 : stacker2 branch timing detection PSE04 : stacker2 approaching detection PSE05 : stacker3 branch timing detection PSE06 : stacker3 approaching detection PSE07 : stacker4 branch timing detection PSE08 : stacker4 approaching detection



Error cause



on reset begin process after changing process mode in aging



Method of check



Measures



come off connector breaking of wire



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



sensor level error



Check to display sensor level(RAS)



Clean sensor



sensor defection



Check to “PORT READ”(RAS) Check port which change sensor status



Adjust sensor or replace Replace verification unit



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Resume process Press CLEAR key.



ERROR TYPE



machine trouble：sensor OFF check error Abstruct



Check timing



Transmitter of sensor stops to emit light but detect light at receiver.



Code, Sensor name, Content 7067 7068 7069 7070 7071 7072 7073 7074 7081 7083 7084 7086 7087 7089 7090 7092 7093 7094 7095 7096 7097 7098 7099 7100 7124 7125 7126 7127



PSE09 : stacker1 bill remaining detection PSE10 : stacker1 bill remaining detection PSE11 : stacker2 bill remaining detection PSE12 : stacker2 bill remaining detection PSE13 : stacker3 bill remaining detection PSE14 : stacker3 bill remaining detection PSE15 : stacker4 bill remaining detection PSE16 : stacker4 bill remaining detection PSE17 : stacker5 branch timing detection PSE18 : stacker5 approaching detection PSE19 : stacker6 branch timing detection PSE20 : stacker6 approaching detection PSE21 : stacker7 branch timing detection PSE22 : stacker7 approaching detection PSE23 : stacker8 branch timing detection PSE24 : stacker8 approaching detection PSE25 : stacker5 bill remaining detection PSE26 : stacker5 bill remaining detection PSE27 : stacker6 bill remaining detection PSE28 : stacker6 bill remaining detection PSE29 : stacker7 bill remaining detection PSE30 : stacker7 bill remaining detection PSE31 : stacker8 bill remaining detection PSE32 : stacker8 bill remaining detection PSD10L : RJ1 bill remaining of inlet (L) PSD10R : RJ1 bill remaining of inlet (R) PSD11L : RJ2 bill remaining of inlet (L) PSD11R : RJ2 bill remaining of inlet (R)



Error cause (1) (2) (1) (2) (1) (2) (1) (2)



Method of check



Measures



come off connector breaking of wire



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



sensor level error



Check to display sensor level(RAS)



Clean sensor



sensor defection



Check to “PORT READ”(RAS) Check port which change sensor status



Adjust sensor or replace Replace verification unit



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



(1) (2) (1) (2) (1) (2) (1) (2)



on reset begin process after changing process mode in aging



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (verification board)



Resume process Press CLEAR key.



ERROR TYPE



machine trouble：communication error between display block Abstruct



Check timing



Receive abnormal response from display block.



communication between main and display block



Code, Sensor name, Content 7901 7902 7903



response time up receive error response data error



Error cause



Method of check



come off connector breaking of wire



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



defection of electric board (DISP board、DISPCPU board)



Check reset machine and do initialize



Replace electric board (DISP board、DISPCPU board)



software defection



ERROR TYPE



Measures



machine trouble：interrupter ON check error Check timing



Interruptor is on through state but can’t detect emitting light.



Code, Sensor name, Content PID02 PID04 PIE02 PIE04 PIE06 PIE08 PIE12 PIE14 PIE16 PIE18



Press CLEAR key.



version up software



Abstruct



8001 8002 8003 8004 8005 8006 8007 8008 8009 8010



Resume process



: : : : : : : : : :



RJ1 full detection RJ2 full detection stacker 1 full detection stacker 2 full detection stacker 3 full detection stacker 4 full detection stacker 5 full detection stacker 6 full detection stacker 7 full detection stacker 8 full detection



in aging



Error cause



Method of check



Measures



interrupter defection



Visually check state of interruptor Check to “PORT READ”(RAS) Check port which change sensor status



Correct to set or replace interruptor



come off connector breaking of wire



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board)



Resume process Press CLEAR key.



ERROR TYPE



operating time over：operating time over Abstruct



Check timing



Detect time over of moving bill holder.



Code, Sensor name, Content 8101 8102



MDCA01,PIA04,05 : at holding bill holder MDCA01,PIA04,05 : at releasing bill holder



moving actuator



Error cause



Method of check



Measures



gap actuator, adjust defection into foreign matter



Visually check actuator



Adjust actuator Remove foreign matter



interrupter defection



Visually check state of interruptor Check to “PORT READ”(RAS) Check port which change sensor status



Correct to set or replace interruptor



come off connector breaking of wire



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



actuator defection slip timing belt, adjust defection



Check to “DRIVE CHECK”(RAS)



Replace actuator Adjust timing belt or replace



defection of electric board (MAINCPU board) (I/O-CORE board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (I/O-CORE board)



Resume process Press CLEAR key.



ERROR TYPE



machine trouble：interrupter OFF check error Abstruct



Check timing



Interruptor stops to emit light but detect light.



Code, Sensor name, Content 8301 8304 8305 8307 8308 8309 8310 8311 8312 8313 8314 8315 8316 8317 8318 8319 8322 8323 8324 8325 8326 8327 8328 8329



PIA01 PIA04 PIA05 PIB01 PID01 PID02 PID03 PID04 PIE01 PIE02 PIE03 PIE04 PIE05 PIE06 PIE07 PIE08 PIE11 PIE12 PIE13 PIE14 PIE15 PIE16 PIE17 PIE18



: : : : : : : : : : : : : : : : : : : : : : : :



upper of bill holder detection bill holder state detection bill holder placement detection feed motor rotate detection RJ1 rotate fan detection RJ1 full detection RJ2 rotate fan detection RJ2 full detection stacker 1 rotate fan detection stacker 1 full detection stacker 2 rotate fan detection stacker 2 full detection stacker 3 rotate fan detection stacker 3 full detection stacker 4 rotate fan detection stacker 4 full detection stacker 5 rotate fan detection stacker 5 full detection stacker 6 rotate fan detection stacker 6 full detection stacker 7 rotate fan detection stacker 7 full detection stacker 8 rotate fan detection stacker 8 full detection



on reset begin process after changing process mode in aging



Error cause



Method of check



Measures



interrupter defection



Visually check state of interruptor Check to “PORT READ”(RAS) Check port which change sensor status



Correct to set or replace interruptor



come off connector breaking of wire



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board)



Resume process Press CLEAR key.



ERROR TYPE



machine trouble：error on verification block Abstruct



Check timing



Error response from verification block or response isn’t correct.



Code, Sensor name, Content 8551 8552 8553 8554 8555 8556 8557 8558 8559 8560 8561 8562 8563 8564 8565 8566 8567 8568 8569 8570 8571



parity error1 response out of command code response out of character code timing error PLD hard error thickness detection communication error parity error1 data error BCC error command time up response time up response data time up adjustment value writing error BV thickness detection error BV hard error ＦＰＧＡ１ BV hard error ＦＰＧＡ２ BV interface error Ｉ／Ｆ１ BV interface error Ｉ／Ｆ２ BV interface error Ｉ／Ｆ３ BV interface error Ｉ／Ｆ４ BV hard error (clock control block) ＦＰＧＡ１



8572 8573



BV hard error (clock control block) ＦＰＧＡ２ come off BV connector



communication between main and BV



Error cause



Method of check



Measures



come off connector breaking of wire



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



defection of electric board (verification board)



Check reset machine and do initialize



Replace electric board (verification board)



Resume process Press CLEAR key.



ERROR TYPE



machine trouble：over load error Abstruct



Check timing



Detect over load of DC motor.



Code, Sensor name, Content 8601 8602



MDCA01ERR,MDCA01 : over current of bill holder motor MDCA01HL,MDCA01 : over current by hard latch of bill holder motor



all time



Error cause



Method of check



Measures



gap actuator, adjust defection into foreign matter



Visually check actuator



Adjust actuator Remove foreign matter



interrupter defection



Visually check state of interruptor Check to “PORT READ”(RAS) Check port which change sensor status



Correct to set or replace interruptor



come off connector breaking of wire



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



actuator defection slip timing belt, adjust defection



Check to “DRIVE CHECK”(RAS)



Replace actuator Adjust timing belt or replace



defection of electric board (MAINCPU board) (I/O-CORE board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (I/O-CORE board)



Resume process Press CLEAR key.



ERROR TYPE



machine trouble：motor driver over heating error Abstruct



Check timing



Detect over heating of motor driver.



rotating motor



Code, Sensor name, Content 8632 8633 8634 8635 8636 8637 8638 8639 8640 8641



SMD01ERR,SMD01 SMD02ERR,SMD02 SME01ERR,SME01 SME02ERR,SME02 SME03ERR,SME03 SME04ERR,SME04 SME05ERR,SME05 SME06ERR,SME06 SME07ERR,SME07 SME08ERR,SME08



ERROR TYPE



: : : : : : : : : :



RJ1 rotate fan motor RJ2 rotate fan motor stacker 1 rotate fan stacker 2 rotate fan stacker 3 rotate fan stacker 4 rotate fan stacker 5 rotate fan stacker 6 rotate fan stacker 7 rotate fan stacker 8 rotate fan



Error cause



motor motor motor motor motor motor motor motor



Method of check



Measures



come off connector breaking of wire



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



actuator defection slip timing belt, adjust defection



Check to “DRIVE CHECK”(RAS)



Replace actuator Adjust timing belt or replace



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board)



Press CLEAR key.



machine trouble：rotate error of cooling fan Abstruct



Check timing



Detect rotate error of cooling fan.



Code, Sensor name, Content 8691 8692 8693



Resume process



PSFANERR1 :cooling fan 1 rotate error PSFANERR2 : cooling fan 2 rotate error FANC_ERR : hopper/reject cooling fan rotate error



all time



Error cause



Method of check



Measures



gap actuator, adjust defection into foreign matter



Visually check actuator



Adjust actuator Remove foreign matter



come off connector breaking of wire



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



defection of electric board (MAINCPU board) (I/O-CORE board) (PWR-DC board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (I/O-CORE board) (PWR-DC board)



Resume process Press CLEAR key.



ERROR TYPE



machine trouble：connector come off Abstruct



Check timing



Detect to come off connector.



Code, Sensor name, Content 8702



CNNKMAIN :in MAINCPU board（ＭＡＩＮＣＰＵ）



8703



CNNKE2P : in MAINCPU board（Ｓｅｃｕｒｉｔｙ）



8704



CNNKBV : in MAINCPU board（ＢＶ）



8705



CNNKCPUA : in MAINCPU board（ＡＲＣ）



8706



CNNKSTDR_1 : in MAINCPU board（ＳＴＤＲ１）



8707



CNNKSTDR_2 : in MAINCPU board（ＳＴＤＲ２）



8708



CNNKLED1 : in MAINCPU board（ＬＥＤ１）



8709



CNNKDISP : in MAINCPU board（ＤＩＳＰ）



8710



CNNKDCPU : in MAINCPU board（ＤＩＳＰＣＰＵ）



8713



CNNKSTDR1 : in STDR_1 board（ＳＴＤＲ１）



8714



CNNKLED2_1 : in STDR_1 board（ＬＥＤ２＿１）



8715



CNNKSTDR2 : in STDR_2 board（ＳＴＤＲ２）



8716



CNNKLED2_2 : in STDR_2 board（ＬＥＤ２＿２）



all time



Error cause come off connector breaking of wire defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (DISP board、DISPCP board) (I/O-CORE board) (security board) (verification board) (LED1 board) (LED2 board)



Method of check Check harness、conduction test (refer wiring diagram) Check reset machine and do initialize



Measures Correct to joint, correct harness line or replace connector Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (DISP board、DISPCP board) (I/O-CORE board) (security board) (verification board) (LED1 board) (LED2 board)



Resume process Turn power off and on. You can execute RAS mode to not turn off power but probably occur another error.



ERROR TYPE



machine trouble：fuse cut Abstruct



Check timing



Detect fuse cut.



all time



Code, Sensor name, Content 8751 8752 8753 8754



POWERFCUT :ＰＷＲ－ＤＣ board MFUSECUT :ＩＯ＿ＣＯＲＥ board FUSECUT : intermediate trans.1 actuate block FUSECUT2 : intermediate trans.2 actuate block



ERROR TYPE



Error cause



Method of check



short circuit of power harness short circuit of actuate harness



Visually check harness Check line of fuse block



Correct to joint, correct harness line or eplace harness or fuse



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (PWR-DC board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board) (PWR-DC board)



machine trouble：polymar switch in tripping state Abstruct



Code, Sensor name, Content MAIN9VDN : down 9V power (reject motor) MAIN5V3DN :down 5V3 power (MAINCPU board)



Resume process Press CLEAR key.



Check timing



Detect polymar switch in tripping state.



8761 8762



Measures



all time



Error cause short circuit of power harness short circuit of actuate harness



Method of check Visually check harness Check line of polymar switch block



Measures Correct to joint, correct harness line or eplace harness or switch



Resume process Turn power off and on. You can execute RAS mode to not turn off power but probably occur another error.



defection of electric board (MAINCPU board) (I/O-CORE board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (I/O-CORE board)



ERROR TYPE



machine trouble：network error Abstruct



Check timing



Detect error of ARC network.



Code, Sensor name, Content 8801 8802 8803 8804 8809



re-config error receiver busy cannot send down other node not exist nodes



ERROR TYPE



all time



Error cause



Method of check



Measures



come off connector breaking of wire



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



defection of electric board (MAINCPU board)



Check reset machine and do initialize



Replace electric board (MAINCPU board)



Press CLEAR key.



machine trouble：FPGA error Abstruct



Check timing



Request control of FPGA but don’t end normal.



Code, Sensor name, Content 8901 8903 8904 8905 8906 8907 8908



Resume process



feed ＤＡＣ転送不能 ＤＡＣ転送タイムオーバー ＲＴＣ転送不能 ＲＴＣ転送タイムオーバー ＥＥＰＲＯＭ転送不能 ＥＥＰＲＯＭ転送タイムオーバー



request control of FPGA



Error cause defection of electric board (MAINCPU board)



Method of check Check reset machine and do initialize



Measures Replace electric board (MAINCPU board)



Resume process Turn power off and on. You can execute RAS mode to not turn off power but probably occur another error.



ERROR TYPE



machine trouble：FPGA initializing error Abstruct



Check timing



Detect error in initializing FPGA.



Code, Sensor name, Content 8921



DONE1 :ＭＡＩＮＣＰＵ board



at power on



Error cause come off connector breaking of wire defection of electric board (MAINCPU board)



ERROR TYPE



Method of check Check harness、conduction test (refer wiring diagram) Check reset machine and do initialize



Measures Correct to joint, correct harness line or replace connector Replace electric board (MAINCPU board)



Turn power off and on. You can execute RAS mode to not turn off power but probably occur another error.



machine trouble：battery error Abstruct



Check timing



Detect battery error at power on.



Code, Sensor name, Content 8931



Resume process



BATNG : battery error



at power on



Error cause



Method of check



Measures



defection of battery



Check voltage of battery(more than 2.5V at power off)



Replace electric board (MAINCPU board)



defection of electric board (MAINCPU board)



Check reset machine and do initialize



Replace electric board (MAINCPU board)



Resume process Press CLEAR key.



ERROR TYPE



machine trouble：voltage error Abstruct



Check timing



Detect moving defection by inter-lock（time over、rotate detection、over heating of motor driver）.



Code, Sensor name, Content 8950



moving defection by inter-lock



ERROR TYPE



Error cause



moving actuator



Method of check



Measures



open the unit



Check switch and detecting plate



Set unit Adjust placement or replace



come off connector breaking of wire



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



switch defection



Check to “PORT READ”(RAS) Check port which change switch status



Replace switch



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (I/O-CORE board)



Resume process Press CLEAR key.



machine trouble：voltage error Abstruct



Check timing



Detect voltage error.



Code, Sensor name, Content 8951



MAINPDN :ＭＡＩＮＣＰＵ power down



8952



MAIN5V4DN :ＭＡＩＮＣＰＵ 5V4 down



8953 8954 8956



STDR1_5VC :ＳＴＤＲ１ 5V error STDR2_5VC :ＳＴＤＲ２ 5V error BVPDN :ＢＶＤＤＣ power down



all time



Error cause



Method of check



Measures



come off connector breaking of wire



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (verification board) (BV-DDC board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (verification board) (BV-DDC board)



Resume process Press CLEAR key.



ERROR TYPE



machine trouble：voltage error Abstruct



Check timing



Detect error of power supply.



at power on on reset



Code, Sensor name, Content 8965 8966



voltage off error voltage on error



ERROR TYPE



Error cause



Method of check



short circuit of power harness short circuit of actuate harness



Visually check harness Check line of fuse block



Correct to joint, correct harness line or eplace harness or fuse



come off connector breaking of wire



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



defection of electric board (MAINCPU board) (STDR1 board、STDR2 board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (STDR1 board、STDR2 board)



machine trouble：setting data error (unmatch) Abstruct



Code, Sensor name, Content CPU-M sensor adjustment data UNIT setting data pattern setting data APL setting data BV suspicious level setting data BV fitness level setting data



Resume process Press CLEAR key.



Check timing



Unmatch between setting data in MAINCPU and in CF card memory.



9001 9003 9005 9006 9007 9008



Measures



at power on on reset



Error cause It doesn’t execute RAS after replacing CF card or MAINCPU board



Method of check Check whether replace CF card or MAINCPU board



Measures “DATA“(RAS) save/load 【replace CF】 MAINCPU→ＣＦ(save) 【replace MAINCPU board】 ＣＦ→MAINCPU(load) 【both】 MAINCPU→ＣＦ(save)



defection of electric board (MAINCPU board) (PWR-DC board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (PWR-DC board)



Resume process Press CLEAR key.



ERROR TYPE



machine trouble：setting data error (unmatch) Abstruct



Check timing on reset



Unmatch between setting data in MAINCPU and in BV.



Code, Sensor name, Content 9009



denomination data



ERROR TYPE



Error cause



Method of check



Measures



It doesn’t execute download after replacing BV or MAINCPU board



Check to download BV program



Download BV program



defection of electric board (MAINCPU board)



Check reset machine and do initialize



Replace electric board (MAINCPU board)



machine trouble：setting data error (BCC error with both memories) Abstruct



9021



CPU-M sensor adjustment data



9023 9025 9026 9027



UNIT setting data pattern setting data APL setting data BV suspicious level setting data



9028



BV fitness level setting data



Press CLEAR key.



Check timing



Detect BCC error with both memories of setting data.



Code, Sensor name, Content



Resume process



at power on on reset



Error cause defection of electric board (MAINCPU board)



Method of check Check reset machine and do initialize



Measures Replace electric board (MAINCPU board)



Resume process Press CLEAR key.



ERROR TYPE



machine trouble：setting data error (BCC error with either memory ) Abstruct



Check timing



Detect BCC error with either memory of setting data.



Code, Sensor name, Content 9041



CPU-M sensor adjustment data



9043 9045 9046 9047



UNIT setting data pattern setting data APL setting data BV suspicious level setting data



9048



BV fitness level setting data



ERROR TYPE



at power on on reset



Error cause defection of electric board (MAINCPU board)



Method of check Check reset machine and do initialize



Replace electric board (MAINCPU board) Set again in RAS



machine trouble：setting data error (BCC error with either memory ) Abstruct



Code, Sensor name, Content denomination data



Resume process Press CLEAR key.



Check timing on reset end of counting



Detect BCC error with either memory of setting data.



9049



Measures



Error cause defection of electric board (MAINCPU board)



Method of check Check reset machine and do initialize



Measures Replace electric board (MAINCPU board) Download BV program



Resume process Press CLEAR key.



ERROR TYPE



machine trouble：port read error Abstruct



Check timing



Detect port read error.



all time



Code, Sensor name, Content 9081



port read error



ERROR TYPE



Error cause defection of electric board (MAINCPU board) (STDR1 board、STDR2 board) (DISP board、DISPCPU board) (I/O-CORE board) (security board) (verification board)



Method of check Check reset machine and do initialize



Measures Replace electric board (MAINCPU board) (STDR1 board、STDR2 board) (DISP board、DISPCPU board) (I/O-CORE board) (security board) (verification board)



Turn power off and on. You can execute RAS mode to not turn off power but probably occur another error.



machine trouble：runaway detection Abstruct



Check timing



Detect of CPU runaway.



Code, Sensor name, Content 9101



Resume process



runaway detection



all time



Error cause defection of electric board (MAINCPU board)



software defection



Method of check Check reset machine and do initialize



Measures Replace electric board (MAINCPU board)



version up software



Resume process Press CLEAR key.



ERROR TYPE



machine trouble：memory error Abstruct



Check timing



Detect memory error.



at power on



Code, Sensor name, Content 9201 9202 9203 9204 9205



MAINCPU ROM error MAINCPU RAM error verification ROM error verification RAM(main) error verification RAM(sub) error



ERROR TYPE



Error cause defection of electric board (MAINCPU board) (verification board)



Method of check Check reset machine and do initialize



Measures Replace electric board (MAINCPU board) (verification board)



Press CLEAR key.



machine trouble：program error Abstruct



Check timing



Detect program error.



Code, Sensor name, Content 9801 9802 9803 9804



Resume process



over the limit time system call error interface error of task function call error



all time



Error cause defection of electric board (MAINCPU board) (verification board) software defection



Method of check Check reset machine and do initialize



Measures Replace electric board (MAINCPU board) (verification board) version up software



Resume process Press CLEAR key.



ERROR TYPE



power failure：power failure Abstruct



Check timing



Power failure occurs in processing.



in processing



Code, Sensor name, Content 9901



power failure in processing



ERROR TYPE



Error cause



Method of check



Measures



Turn off power by plug or breaker



Listen situation from user



Explain to user



come off connector breaking of wire



Check harness、conduction test (refer wiring diagram)



Correct to joint, correct harness line or replace connector



short circuit of power supply



Check harness、conduction test (refer wiring diagram)



Solve cause of short circuit and turn on breaker



defection of power supply



Check power supply



Replace power supply



defection of electric board (MAINCPU board) (DISP board、DISPCPU board)



Check reset machine and do initialize



Replace electric board (MAINCPU board) (DISP board、DISPCPU board)



Press CLEAR key.



machine trouble：receive AC command Abstruct



Check timing



Receive AC command.



Code, Sensor name, Content 9903



Resume process



receive AC command



all time



Error cause software defection



Method of check Check reset machine and do initialize



Measures version up software



Resume process Press CLEAR key.