12 0 980 KB
文档名称
文档密级
link configuration guide for XMC-5D 1. 2+0 (XPIC) This section uses the data configured on the RTN 950 as an example to implement the configuration. The configuration methods for other devices are similar. 1.1 Networking Diagram
1.2 Configuration Process Step 1 Change the running mode of the IF port to IS8.
2020-1-12
华为保密信息,未经授权禁止扩散
第 1 页, 共 7 页
文档名称
文档密级
Step 2 Change the multiplexing mode of the IF port to Share ODU
Step 3 Configure XPIC group
2020-1-12
华为保密信息,未经授权禁止扩散
第 2 页, 共 7 页
文档名称
文档密级
2. 2+SD(XPIC) This section uses the data configured on the RTN 950 as an example to implement the configuration. The configuration methods for other devices are similar. 2.1 Networking Diagram
2.2 Configuration Process The Step 1 to Step 3 is same as 2+0(XPIC) configuration. It need to pay attention the XPIC must be intra-board. In this case: XPIC group 1 is 3-ISM8-1(H) & 3-ISM8-2(V) XPIC group 2 is 5-ISM8-1(H) & 5-ISM8-2(V) Step 4 configure 1+1 SD group The 1+1 SD group must be paired slot, in this case: 1+1 SD group 1 is 3-ISM8-1 & 5-ISM8-1 1+1 SD group 2 is 3-ISM8-2 & 5-ISM8-2
2020-1-12
华为保密信息,未经授权禁止扩散
第 3 页, 共 7 页
文档名称
文档密级
3. 4+0(XPIC) This section uses the data configured on the RTN 950 as an example to implement the configuration. The configuration methods for other devices are similar. 3.1 Networking Diagram
3.2 Configuration Process Step 1 Change the cascading port mode of the NE to CA.
2020-1-12
华为保密信息,未经授权禁止扩散
第 4 页, 共 7 页
文档名称
文档密级
Step 2 Change the running mode of the IF port to IS8.
Step 3 Change the multiplexing mode of the IF port to Share ODU.
2020-1-12
华为保密信息,未经授权禁止扩散
第 5 页, 共 7 页
文档名称
文档密级
Step 4 Create a CA group.
Step 5 Configure XPIC protection.
2020-1-12
华为保密信息,未经授权禁止扩散
第 6 页, 共 7 页
文档名称
文档密级
4. 4+SD(XPIC) This section uses the data configured on the RTN 950 as an example to implement the configuration. The configuration methods for other devices are similar. 4.1 Networking Diagram
4.2 Configuration Process The Step 1 to Step 5 is same as 4+0(XPIC) configuration. It need to pay attention the XPIC must be intra-board. In this case: XPIC group 1 is 3-ISM8-1(H) & 3-ISM8-2(V) XPIC group 2 is 4-ISM8-1(H) & 4-ISM8-2(V) XPIC group 3 is 5-ISM8-1(H) & 5-ISM8-2(V) XPIC group 4 is 6-ISM8-1(H) & 6-ISM8-2(V) Step 6 configure 1+1 SD group The 1+1 SD group must be paired slot, in this case: 1+1 SD group 1 is 3-ISM8-1 & 5-ISM8-1 1+1 SD group 2 is 3-ISM8-2 & 5-ISM8-2 1+1 SD group 3 is 4-ISM8-1 & 6-ISM8-1 1+1 SD group 4 is 4-ISM8-2 & 6-ISM8-2
2020-1-12
华为保密信息,未经授权禁止扩散
第 7 页, 共 7 页