4 0 2 MB
Logging Equipment Head LEH-QT Maintenance SWI - FIT Reference: Version: Release Date:
InTouch Content ID 6586450 1.3 23-Sep-2016
EDMS UID:
1658506138
Produced: Owner: Author:
31-Oct-2016 15:23:03 HCS InTouch Brian Philpott
Private
Copyright © 2016 Schlumberger, Unpublished Work. All rights reserved.
LEH-QT
LEH-QT FIT Maintenance Standard Work Instruction / Legal Information
Legal Information
HCS InTouch\Brian Philpott\InTouch Content ID 6586450\1.3\Release Date:23-Sep-2016\EDMS UID: 1658506138\Produced: 31-Oct-2016 15:23:03
Copyright © 2016 Schlumberger, Unpublished Work. All rights reserved. This work contains the confidential and proprietary trade secrets of Schlumberger and may not be copied or stored in an information retrieval system, transferred, used, distributed, translated or retransmitted in any form or by any means, electronic or mechanical, in whole or in part, without the express written permission of the copyright owner. Trademarks & Service marks Schlumberger, the Schlumberger logotype, and other words or symbols used to identify the products and services described herein are either trademarks, trade names or service marks of Schlumberger and its licensors, or are the property of their respective owners. These marks may not be copied, imitated or used, in whole or in part, without the express prior written permission of Schlumberger. In addition, covers, page headers, custom graphics, icons, and other design elements may be service marks, trademarks, and/or trade dress of Schlumberger, and may not be copied, imitated, or used, in whole or in part, without the express prior written permission of Schlumberger. A complete list of Schlumberger marks may be viewed at the Schlumberger Oilfield Services Marks page: http://markslist.slb.com
Private Copyright © 2016 Schlumberger, Unpublished Work. All rights reserved.
LEH-QT FIT Maintenance Standard Work Instruction / Document Control
HCS InTouch\Brian Philpott\InTouch Content ID 6586450\1.3\Release Date:23-Sep-2016\EDMS UID: 1658506138\Produced: 31-Oct-2016 15:23:03
Document Control Owner:
HCS InTouch
Author:
Brian Philpott
Reviewer:
Scott Carson
Approver:
Spoorthy Prakash
Contact Information Name: LDAP Alias:
HCS InTouch intouch-hcs-wl-doc
Revision History Version Date
Description
Prepared by
1.3
23-Sep-2016 As per InTouch feedback 6906337, added step Author: T.Harrison 12 and graphic to Chapter 3
1.2
08-Apr-2016 Removed the checklist; Per InTouch ticket 6824693 corrected the link to the ECRI-E FIT SWI
1.1
15-Sep-2015 As per InTouch feedback 6713121, updated Author: B. Philpott, J. Singh illustration in step 2 of section 5: Lubricate and Reassemble (5 min).
1.0
17-Apr-2015 Initial release
Author: B. Philpott
Field Test
14-Dec-2014 Initial issue for Field Test.
Author: Brian Philpott
Author: Sahar Othman
Private Copyright © 2016 Schlumberger, Unpublished Work. All rights reserved.
iv
LEH-QT FIT Maintenance Standard Work Instruction / Table of Contents
iv
HCS InTouch\Brian Philpott\InTouch Content ID 6586450\1.3\Release Date:23-Sep-2016\EDMS UID: 1658506138\Produced: 31-Oct-2016 15:23:03
Table of Contents 1
General Instructions
2
Summary for FIT
3
Perform Mechanical Checks (5 min)
4 4.1 4.2 4.3
_____________________________________________
1
_________________________________________________
3
______________________________
4
Perform Electrical Checks (5 min) ________________________________ Prepare the 31-pin Extender ____________________________________ Perform a conductor continuity check ___________________________ Perform an insulation resistance check __________________________
8 8 8 9
5
Lubricate and Reassemble (5 min)
6
Update the RITE Work Order (5 min)
______________________________
12
_____________________________
14
Private Copyright © 2016 Schlumberger, Unpublished Work. All rights reserved.
1
LEH-QT FIT Maintenance Standard Work Instruction / General Instructions
1
General Instructions
HCS InTouch\Brian Philpott\InTouch Content ID 6586450\1.3\Release Date:23-Sep-2016\EDMS UID: 1658506138\Produced: 31-Oct-2016 15:23:03
The following Standard Work Instruction is intended as a primary reference guide to the LEH-QT Maintenance FIT. For more details, refer to Heads Operations and Maintenance Manual (Intouch Content ID: 3012542).
Total Process Time: 20 minutes Note The total process time does NOT include the preparation time.
Legend
!
Note
Lubricate with specified oil
QHSE critical step
Lubricate with specified grease
Replace
Use specified threadlocking fluid
Inspect Clean Use specified handtool Torque Good example Bad example
Check with meter Process sequence Spill generated ESD protection required
Information Sources Description
InTouchSupport ID
Heads Maintenance manual
Intouch Content ID: 3012542
Logging Heads Reference page
Intouch Content ID: 3258451
Private Copyright © 2016 Schlumberger, Unpublished Work. All rights reserved.
1
2
LEH-QT FIT Maintenance Standard Work Instruction / General Instructions
Procedure Requirements Task Requirements and Information Proficiency:
Trained operator LEH-QT is attached to the wireline cable.
Equipment status
LEH-QT has been cleaned.
HCS InTouch\Brian Philpott\InTouch Content ID 6586450\1.3\Release Date:23-Sep-2016\EDMS UID: 1658506138\Produced: 31-Oct-2016 15:23:03
General Required Tools Description
Part No. B003984
C-spanner
H268423
Hammer
B015477
Punch Allen wrench set
T6005202
Ohmmeter
500 V Megger
B013366
Lubriplate grease
B021698
DC-111
H245349
31-pin Extender
Grease guns, self priming
Spare Parts Required Spares Part No.
Description
N/A
N/A
Private Copyright © 2016 Schlumberger, Unpublished Work. All rights reserved.
2
3
LEH-QT FIT Maintenance Standard Work Instruction / Summary for FIT
HCS InTouch\Brian Philpott\InTouch Content ID 6586450\1.3\Release Date:23-Sep-2016\EDMS UID: 1658506138\Produced: 31-Oct-2016 15:23:03
2
Summary for FIT
Private Copyright © 2016 Schlumberger, Unpublished Work. All rights reserved.
3
4
LEH-QT FIT Maintenance Standard Work Instruction / Perform Mechanical Checks
4
(5 min)
Perform Mechanical Checks (5 min)
3 Step
HCS InTouch\Brian Philpott\InTouch Content ID 6586450\1.3\Release Date:23-Sep-2016\EDMS UID: 1658506138\Produced: 31-Oct-2016 15:23:03
1.
Action
Figure
Wash the head clean to remove the mud deposited while pulling out of hole in the last descent. Verify mud deposits are removed from the thermometer housings and the fishing neck.
2.
Inspect the fishing neck for burrs or nicks that can cause damage to the cable armor.
nicks burrs
Replaced if damaged.
3.
Inspect the 2 coiled spring pins (B013813) in the fishing neck: - correct length - bent - position.
4.
Inspect the tightness of the 4 screws (100320987) in the fishing neck.
5.
Inspect the position of the snap ring (H329445) on the fishing neck.
Note Verify the opening in the snap ring is NOT positioned over the gap where the two halves of the fishing neck meet. This ensures equal coverage over both halves of the fishing neck.
tightness
Top half of finshing neck
Snap ring
Fishing neck halves mate up
Bottom half of fishing neck
Private Copyright © 2016 Schlumberger, Unpublished Work. All rights reserved.
snap ring gap
5
LEH-QT FIT Maintenance Standard Work Instruction / Perform Mechanical Checks
5
(5 min) Step 6.
Action
Figure
Inspect the grooved pin (B032902) in the outer housing (H701907).
Pin B032902
HCS InTouch\Brian Philpott\InTouch Content ID 6586450\1.3\Release Date:23-Sep-2016\EDMS UID: 1658506138\Produced: 31-Oct-2016 15:23:03
- verify the pin is installed - verify the alignment of the pin.
installed alignment
Outer housing H701907
7.
Inspect the coiled spring pin (B013394) in the fishing bell extension (H701908).
installed alignment Pin B013394
- verify the pin is installed - verify the alignment of the pin.
Outer housing H701907
8.
Inspect the three thermometer housings. - damage to the housings or pins - missing housing - bent / missing pins - loose pins.
Fishing bell extension H701908
Thermometer housing assembly H245662
Note If running thermometers/thermal strips, remove and replace the thermometers/thermal strips at this time. Retaining collar
Thermometer
Fishing bell extension H701908
Fishing bell H231884
Fishing bell
Note If running a weakpoint, verify the color of the band on the weakpoint by looking through the thermometer housing slot.
Private Copyright © 2016 Schlumberger, Unpublished Work. All rights reserved.
damage to housing damage to pins missing housings bent / missing pins loose pins
Retainer collar H245493
6
LEH-QT FIT Maintenance Standard Work Instruction / Perform Mechanical Checks
6
(5 min) Step 9.
Action Inspect the three spirol pins (B013394) holding the thermometer housings in the fishing bell.
HCS InTouch\Brian Philpott\InTouch Content ID 6586450\1.3\Release Date:23-Sep-2016\EDMS UID: 1658506138\Produced: 31-Oct-2016 15:23:03
- verify the pin is installed - verify the alignment of the pin.
Figure installed alignment Pins(3) B013394
Fishing bell H231884
10.
Inspect the 3 screws on the retainer collar for:
tightness damage
- tightness, - damage.
Screw H251222
Screws (2) H251223
If screws are damaged, replace them
Fishing bell H231884
11.
Retainer collar H245493
Inspect threaded ring (H222685).
Note Ensure the fishing bell (H231884) is properly made-up to the bell housing extension (H701310).
12.
Inspect and clean the grease fitting (A017129) in the bell housing extension (H701310).
Grease fitting A017129
Private Copyright © 2016 Schlumberger, Unpublished Work. All rights reserved.
Bell housing extension H701310
7
LEH-QT FIT Maintenance Standard Work Instruction / Perform Mechanical Checks
7
(5 min) Step 13.
Action
Figure
Inspect the two grooved pins (B033000) in the bell housing extension (H701310).
Pins (2) B033000
HCS InTouch\Brian Philpott\InTouch Content ID 6586450\1.3\Release Date:23-Sep-2016\EDMS UID: 1658506138\Produced: 31-Oct-2016 15:23:03
- verify the pin is installed - verify the alignment of the pin.
Fishing bell H231884
14.
installed alignment
Bell housing extension H701310
Inspect the set screw (B033748) on the bell housing extension. - verify screw is installed - tightness of screw.
Bell housing extension
Screw B033748 tightness damage
15.
Inspect the threads of the lower bulkhead (H701315). - clean - no galling.
Bell housing extension H701310
Lower bulkhead H701315
Threads
16.
Inspect the pins inside the lower contact assembly (H441577): - dirt inside and around the socket - damage to the socket - damage to the pins - bent or pushed in.
Bulkhead H701315
31-pin head H441578
Pins H222115
Lower Contact Assy. - dirt - socket damage - pin damage
Private Copyright © 2016 Schlumberger, Unpublished Work. All rights reserved.
8
LEH-QT FIT Maintenance Standard Work Instruction / Perform Electrical Checks (5 min)
Perform Electrical Checks (5 min)
4
HCS InTouch\Brian Philpott\InTouch Content ID 6586450\1.3\Release Date:23-Sep-2016\EDMS UID: 1658506138\Produced: 31-Oct-2016 15:23:03
This section is for electrical inspection of the the LEH-QT with a bulkhead to head adapter (H701416). If running and ECRD and an ECRI bulkhead (100082292), go to the electrical inspection section of the ECRI SWI 6632333.
Potential Severity: Serious Potential Loss: Personnel Hazard Category: Electrical
Electrical damage to the ECRI bulkhead can occur if improper continuity and insulation resistance checks are performed.
Prepare the 31-pin Extender
4.1 Step 1.
Action
Figure
Insert the 31-pin extender (H245349) into the downhole end of the LEH-QT. 31-pin extender H245349
2.
Set the toggle switch to “1 AND 4 DISCONNECT”.
Quality Note Using the proper extender (H245349) ensures that voltage is not applied to load cell lines 14, 15, 19 and 20.
4.2
Perform a conductor continuity check Check conductor continuity with a Simpson meter or equivalent for each conductor: 1 thru 7 and 10.
Private Copyright © 2016 Schlumberger, Unpublished Work. All rights reserved.
8
9
LEH-QT FIT Maintenance Standard Work Instruction / Perform Electrical Checks (5
9
min)
HCS InTouch\Brian Philpott\InTouch Content ID 6586450\1.3\Release Date:23-Sep-2016\EDMS UID: 1658506138\Produced: 31-Oct-2016 15:23:03
Step
Action
1.
Set the Simpson meter on high scale 0–100.
2.
Put the CSS in the CIS position.
3.
Place the red lead in position number 1 on the 31-pin extender.
4.
Clip the black lead to mass (bulkhead - H701315).
5.
Short out line 1 to mass at the CIS.
Note The resistance should be equal to the resistance of the cable conductor line plus ground. If the continuity reading is not acceptable, troubleshoot the problem.
Note Troubleshooting consist of checking BCC connections and downhole hook-up wires. Refer to the LEH-QT SLS-1 SWI, InTouch 6586651. 6.
Repeat steps 1 through 5 for lines 2 thru 7 and 10. Remember to move the red lead to the next position on the 31-pin extender and short out the corresponding line at the CIS.
7.
4.3
Insert the black lead in position 28 and the red lead in position 29 of the 31-pin extender. Resistance should be less than 1 ohm.
Perform an insulation resistance check Potential Severity: Serious Potential Loss: Personnel Hazard Category: Electrical
There is a potential for electrical shock when performing the insulation resistance test.
Private Copyright © 2016 Schlumberger, Unpublished Work. All rights reserved.
10
LEH-QT FIT Maintenance Standard Work Instruction / Perform Electrical Checks (5 min) Bulkhead H701315
Black clipped to bulkhead
HCS InTouch\Brian Philpott\InTouch Content ID 6586450\1.3\Release Date:23-Sep-2016\EDMS UID: 1658506138\Produced: 31-Oct-2016 15:23:03
Push to apply 500 VDC
Step
31-pin extender
Action
Figure
1.
Put the CSS in the CIS position.
2.
Place the positive lead (red) of the megger on position 1 in the 31-pin extender (H245349).
3.
Place the common lead (black) on the body of the bulkhead.
4.
Measure the IR. The insulation resistance should be greater than 500 Mohms. If the IR reading is not acceptable, troubleshoot the problem.
Note Troubleshooting consist of checking BCC connections and downhole hook-up wires. Refer to the LEH-QT SLS-1 SWI, InTouch 6586651. 5.
Repeat steps 2 through 4 for wires 2 thru 7, 28 to mass and 29 to mass.
Note Line 10 is connected to mass; therefore, it will be continuous. 6.
Check the insulation resistance between each conductor. Place the black lead in position one and the red lead in position 2 of the 31-pin extender.
Leave the black lead on a conductor, move the red lead to each of the remaining conductors
Take the measurement. The insulation resistance should be greater than 500 Mohms. Move the red lead to the next conductor.
7.
Repeat step 6 for the remaining lines. Black lead to position 2, red lead to positions 3 thru 7 Black lead to position 3, red lead to positions 4 thru 7 Black lead to position 4, red lead to positions 5 thru 7 Black lead to position 5, red lead to positions 6 thru 7 Black lead to position 6, red lead to positions 7
Private Copyright © 2016 Schlumberger, Unpublished Work. All rights reserved.
10
11
LEH-QT FIT Maintenance Standard Work Instruction / Perform Electrical Checks (5 min) Step
HCS InTouch\Brian Philpott\InTouch Content ID 6586450\1.3\Release Date:23-Sep-2016\EDMS UID: 1658506138\Produced: 31-Oct-2016 15:23:03
8.
9.
Action Discharge the voltage from the head hook-up wires by placing a wire on the bulkhead and then touching each of the ports in the 31–pin extender.
Figure
Ground on end to bulkhead
Remove the 31-pin extender (H245349).
Private Copyright © 2016 Schlumberger, Unpublished Work. All rights reserved.
Insert into each port of 31-pin extender
11
12
LEH-QT FIT Maintenance Standard Work Instruction / Lubricate and Reassemble (5
12
min)
Lubricate and Reassemble (5 min)
5 Step
HCS InTouch\Brian Philpott\InTouch Content ID 6586450\1.3\Release Date:23-Sep-2016\EDMS UID: 1658506138\Produced: 31-Oct-2016 15:23:03
1.
Action
Figure
Fill the fishing bell extension (H701908) with DC-111 using the grease gun with the beveled end.
DC-111
Fishing bell extension H701908
Outer housing H701907
2.
Fill the fishing bell (H231884) with DC-111 using the grease gun with the beveled end.
DC111
Fishing bell H231884
3.
Pump Lubriplate into the split threaded ring (H222685) using the grease gun with the beveled end.
Lubriplate
Fishing bell H231884 Split threaded ring H222685
4.
Fill the bell housing extension (H701310) with DC-111 using the grease gun with the female end.
Bell housing extension H701310
DC111
Fishing bell H231884
Private Copyright © 2016 Schlumberger, Unpublished Work. All rights reserved.
Bell housing extension H701310
13
LEH-QT FIT Maintenance Standard Work Instruction / Lubricate and Reassemble (5
13
min) Step
HCS InTouch\Brian Philpott\InTouch Content ID 6586450\1.3\Release Date:23-Sep-2016\EDMS UID: 1658506138\Produced: 31-Oct-2016 15:23:03
5.
Action
Figure
Apply Lubriplate to the threads of bulkhead (H701315).
Lubriplate threads
Bulkhead H701315
6.
If the LEH-QT is not being attached to the toolstring, lubricate the thread protector with Lubriplate and install onto the bulkhead.
Lubriplate
Bulkhead H701315
Private Copyright © 2016 Schlumberger, Unpublished Work. All rights reserved.
O-ring B012828
Thread protector H251929
14
LEH-QT FIT Maintenance Standard Work Instruction / Update the RITE Work Order (5 min)
Update the RITE Work Order (5 min)
6
HCS InTouch\Brian Philpott\InTouch Content ID 6586450\1.3\Release Date:23-Sep-2016\EDMS UID: 1658506138\Produced: 31-Oct-2016 15:23:03
Step
Action
1.
Update the RITE work order with all the information.
2.
Click on Edit when the procedure is completed.
3.
Click on Checklist and answer all checks one after the other.
4.
Fill in the Checklist Remarks.
5.
Add the part number and quantity for parts which were replaced.
6.
Fill in the time taken to complete the procedure.
7.
Change the work order detailed status to closed.
Private Copyright © 2016 Schlumberger, Unpublished Work. All rights reserved.
14