21 0 1 MB
INTERNATIONAL STANDARD
ISO 6789-1 First edition 2017-02
Assembly tools for screws and nuts — Hand torque tools —
Part 1:
Requirements and methods for design conformance testing and quality conformance testing: minimum requirements for declaration of conformance Outils de manoeuvre pour vis et écrous — Outils dynamométriques à commande manuelle — Partie 1: Exigences et méthodes d’essai pour vérifier la con formité de conception et la con formité de qualité: exigences minimales pour déclaration de con formité
Reference number ISO 6789-1:2017(E) © ISO 2017
ISO 6789-1:2017(E)
COPYRIGHT PROTECTED DOCUMENT © ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part o f this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country o f
the requester.
ISO copyright o ffice
Ch. de Blandonnet 8 • CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 [email protected] www.iso.org
ii
© ISO 2017 – All rights reserved
ISO 6789-1:2017(E)
Contents
Page
Foreword ........................................................................................................................................................................................................................................ iv Introduction ................................................................................................................................................................................................................................ vi 1 Scope ................................................................................................................................................................................................................................. 1 2 Normative references ...................................................................................................................................................................................... 1 3 Terms, definitions and symbols ............................................................................................................................................................ 1 ....................................................................................................................................................................... 1 ............................................................................................................................................. 3 4 Classification ............................................................................................................................................................................................................ 3 5 Requirements .......................................................................................................................................................................................................... 3 5.1 Design conformance testing ........................................................................................................................................................ 3 5.1.1 General...................................................................................................................................................................................... 3 5.1.2 Maximum torque values ............................................................................................................................................ 4 ................................................................................................................................................ 4 .......................................................................................................................................... 4 5.1.5 Maximum permissible deviation ....................................................................................................................... 5 5.1.6 Overloading test ............................................................................................................................................................... 5 5.1.7 Endurance test ................................................................................................................................................................... 5 5.1.8 Effect of geometric changes .................................................................................................................................... 6 ....................................................................................................................................................... 7 f 5.3 Conformance test during use ...................................................................................................................................................... 7 6 Torque measurement ...................................................................................................................................................................................... 7 ..................................................................................................................................................... 7 6.2 Application of torque ......................................................................................................................................................................... 8 6.3 Ambient conditions ............................................................................................................................................................................. 8 6.4 Measurement requirements ........................................................................................................................................................ 9 6.5 Measurement sequence................................................................................................................................................................ 11 6.5.1 General................................................................................................................................................................................... 11 .......................................................................................................................... 11 ................................................................................................................................ 11 7 Calculation of deviation ............................................................................................................................................................................. 12 7.1 General ........................................................................................................................................................................................................ 12 7.2 Calculation example 1 .................................................................................................................................................................... 12 7.3 Calculation example 2 .................................................................................................................................................................... 13 8 Declaration of conformance .................................................................................................................................................................. 14 9 Marking ....................................................................................................................................................................................................................... 15 Annex A (normative) Examples of indicating torque tools (Type I) ................................................................................. 16 Annex B (normative) Examples of setting torque tools (Type II) ........................................................................................ 17 Annex C (informative) Measurement sequence flowchart for torque tools .............................................................. 19 Bibliography ............................................................................................................................................................................................................................. 22 3 .1
Terms and definitio ns
3 .2
Symb o ls , des ignatio ns and units
5 .1 .3
S p ecified to rque range
5 .1 .4
S cales , dials and dis p lays
5 .2
Quality co n o rmance tes ting
6.1
To rque meas urement sys tem
6.5 .2
I ndicating to rque to o ls , Typ e I
6.5 .3
S etting to rque to o ls , Typ e I I
© ISO 2017 – All rights reserved
iii
ISO 6789-1:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work o f preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters o f electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the di fferent types o f ISO documents should be noted. This document was dra fted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso .org/directives). Attention is drawn to the possibility that some o f the elements o f this document may be the subject o f patent rights. ISO shall not be held responsible for identi fying any or all such patent rights. Details o f any patent rights identified during the development o f the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso .org/patents).
Any trade name used in this document is in formation given for the convenience o f users and does not
constitute an endorsement.
For an explanation on the voluntary nature o f standards, the meaning o f ISO specific terms and expressions related to con formity assessment, as well as in formation about ISO’s adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso .org/iso/foreword .html. This document was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 10, Assembly tools for screws and nuts, pliers and nippers. This first edition o f ISO 6789-1, together with ISO 6789-2, cancels and replaces ISO 6789:2003 which has been technically revised with changes as follows. a) ISO 6789:2003 has been divided into two parts. This document specifies the requirements for design and manu facture including the content o f a declaration o f con formance. ISO 6789-2 specifies the requirements for traceable certificates o f calibration. It includes a method for calculation o f
uncertainties and provides a method for calibration of the torque measurement device used for calibrating hand torque tools. b) The output drive designation of torque tools is expanded to include hexagonal and other output drives. c) The definition o f the torque range o f the tools has been changed. d) The rate o f loading (shown by the time to achieve the last 20 %) has been changed.
e) The importance of avoiding parasitic forces has been emphasized. f
) Explanatory flowcharts for the measurement sequence o f di fferent torque tools have been added in
Annex C. g) The requirement for a “declaration of conformance” that the torque tool conforms with this document has been added.
h) The requirement for a “certificate o f calibration” has been removed, recognizing that manu facturers’ calibration certificates have not previously contained enough in formation to be traceable calibration certificates. i)
iv
ISO 6789 has been editorially updated and restructured.
© ISO 2017 – All rights reserved
I SO 6 7 8 9 - 1 : 2 0 1 7 (E)
Figures B.2, B.3, B.5 and B.6 have been changed. A list of all parts in the ISO 6789 series can be found on the ISO website.
j)
© ISO 2017 – All rights reserved
v
ISO 6789-1:2 017(E)
Introduction
The revision of ISO 6789:2003 has been designed to achieve the following improvements. ISO 6789 has been split to provide two levels of documentation. It recognizes the different needs of different users of the standard. This document continues to provide designers and manufacturers with relevant minimum requirements for the development, production and documentation of hand torque tools. ISO 6789-2 provides detailed methods for calculation of uncertainties and requirements for calibrations.
This will allow users o f calibration services to more easily compare the calibrations from di fferent laboratories. Additionally, minimum requirements for the calibration o f torque measurement devices
are described in ISO 6789-2:2017, Annex C.
vi
© ISO 2017 – All rights reserved
INTERNATIONAL STANDARD
ISO 6789-1:2017(E)
Assembly tools for screws and nuts — Hand torque tools —
Part 1:
Requirements and methods for design conformance testing and quality conformance testing: minimum requirements for declaration of conformance 1 Scope T h i s do c u ment s p e ci fie s the con forma nce te s ti ng and marki ng re qu i rements
for control le d
for h and
torque to ol s u s e d
tighten i ng o f s crews a nd nuts . I t a l s o s p e c i fie s the m i n i mu m re qu i rements
of conformance for hand torque tools.
for de claration
T h i s do c u ment appl ie s to h and torque to ol s wh ich are cla s s i fie d a s i nd ic ati ng torque to ol s ( Typ e I ) and s e tti ng torque to ol s ( Typ e I I ) .
NO TE
H a nd torque to ol s
covere d b y th i s
do c u ment a re tho s e identi fie d i n I S O
170 3 : 2 0 0 5
b y re ference
nu mb ers 6 1 0 0 1 1 0 , 6 1 0 0 1 1 1 a nd 6 1 0 0 1 2 0 , 6 1 0 0 1 2 1 a nd 6 1 0 0 14 0 , 6 1 0 0 1 5 0 . I S O 170 3 i s c u r rentl y
under revision. In the next edition, torque tools will be moved to an own clause, and with this change the reference numbers will also change and additional reference numbers will be added.
T h i s do c ument do e s no t s p e ci fy re qu i rements o f c a l ibration cer ti fic ate s
are described in ISO 6789-2.
for
hand torque to ol s . T he s e
2 Normative references T he
fol lowi ng
do c u ments are re ferre d to i n the tex t i n s uch a way th at s ome or a l l o f thei r content
con s titute s re qu i rements o f th i s do c u ment. For date d re ference s , on ly the e d ition cite d app l ie s . For u ndate d re ference s , the late s t e d ition o f the re ference d do c ument (i nclud i ng a ny amend ments) appl ie s .
ISO 1173, Assembly tools for screws and nuts — Drive ends for hand- and machine-operated screwdriver bits and connecting parts — Dimensions, torque testing
ISO 1174-1, Assembly tools for screws and nuts — Driving squares — Part 1: Driving squares for hand socket tools
ISO 6789-2:2017, Assembly tools for screws and nuts — Hand torque tools — Part 2: Requirements for calibration and determination o f measurement uncertainty ISO/IEC 17025, General requirements for the competence of testing and calibration laboratories 3 Terms, definitions and symbols 3.1 Terms and definitions For the pu r p o s e s o f th i s do c u ment, the
fol lowi ng
term s and defi n ition s apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses: — IEC Electropedia: available at http://www.electropedia .org/ — ISO Online browsing platform: available at http://www.iso .org/obp © ISO 2017 – All rights reserved
1
ISO 6789-1:2017(E) 3.1.1 design conformance test technical examination o f con formance with those requirements to be met during design or modification
of hand torque tools
3.1.2 quality conformance test
technical examination of conformance with those requirements to be met during manufacture of hand torque tools 3.1.3 declaration of conformance documented in formation provided by the manu facturer that the torque tool complies with the
requirements of this document
3.1.4 maximum permissible deviation
maximum value of relative measurement deviation of the observed torque value on the torque measurement device measured as a percentage of the target torque value on the torque tool Note 1 to entry: Sometimes the term “accuracy” is still used in place o f the term “maximum permissible deviation” which is, however, not technically correct. The concept “measurement accuracy” is not a quantity and is not given a numerical quantity value. A measurement is said to be more accurate when it o ffers a smaller measurement
deviation.
Note 2 to entry: Maximum permissible deviation is di fferent from measurement error which is used in ISO 6789-2 and defined in ISO/IEC Guide 99.
3.1.5 torque measurement system combination o f a torque measurement device and the loading system for application o f torque that acts
as the measurement standard for the hand torque tool
Note 1 to entry: A calibration system as defined in ISO 6789-2 can also be used as a torque measurement system
in this document.
3.1.6 torque measurement device working measurement standard provided either mechanically or by an electronic torque transducer and display 3.1.7 indicating torque tool (Type I) tool that indicates by means o f a mechanical scale, dial or electronic display, the value o f torque exerted by the tool at the output drive 3.1.8 setting torque tool (Type II) tool sensing torque transmitted by comparing the torque applied with a sel f-contained standard and signalling the transmission o f the pre-selected value by a physical impulse, with or without audible signal, causing a temporary reduction in the torque applied 3.1.9 adjustable graduated torque tool (Type II, Class A, Class D and Class G) tool designed to be adjusted by the user, which has a scale or a display to assist adjustment 3.1.10 adjustable non-graduated torque tool (Type II, Class C and Class F) tool designed to be adjusted by the user with the aid o f a torque measurement system
2
© ISO 2017 – All rights reserved
ISO 6789-1:2 017(E)
3.1.11
tool not designed to be adjusted by the user, i.e. having a single setting t
o
r
q
u
3.2
e
t o
o
l
w
i
t
h
f i
x e
d
a
d
j
u
s
t
m
e
n
t
(
T y
p
e
I
I
,
C
l
a
s
s
B
a
n
d
C
l
a
s
s
E
)
Symbols, designations and units
The designations used in this document are indicated in Table 1. Table 1 — Symbols, designations and units Symbol
Designation
Relative deviation of the torque tool from the target torque
ad
Xo
C
l
a
s
%
Value o f torque desired, which may be the indicated, set, nominal value, depending on N ⋅ m the type and class o f the torque tool Observed value shown by the torque measurement device N⋅m
Xt
4
Unit
s
i
f i
c
a
t i
o
n
The hand torque tools to which this document applies are classified as follows. a) Indicating torque tools (Type I; see Annex A): 1) Class A: Wrench, torsion or flexion bar; 2) Class B: Wrench, rigid housing, with scale or dial or display; 3) Class C: Wrench, rigid housing and electronic measurement; 4) Class D: Screwdriver, with scale or dial or display; 5) Class E: Screwdriver, with electronic measurement;
b) Setting torque tools (Type II; see Annex B):
1) Class A: Wrench, adjustable, graduated or with display; 2) Class B: Wrench, fixed adjustment; 3) Class C: Wrench, adjustable, non-graduated; 4) Class D: Screwdriver, adjustable, graduated or with display; 5) Class E: Screwdriver, fixed adjustment; 6) Class F: Screwdriver, adjustable, non-graduated; 7) Class G: Wrench, flexion bar, adjustable, graduated 5
Requirements
5.1 5.1.1
Design conformance testing General
The manu facturer shall veri fy that the torque tool is in con formity with 5.1.2 to 5.1.8.
© ISO 2017 – All rights reserved
3
ISO 6789-1:2017(E)
5.1.2
Maximum torque values
The size of the output drive limits the maximum torque value of the respective torque tool. The assignment is carried out according to the values given in Table 2 . For outputs not specified in Table 2, the size o f the output drive is determined by the maximum torque o f the respective torque tool and shall comply with the requirements given in 5.1.6 and 5.1.8. Table 2 — Maximum torque values of the torque tool Square output drive
a b 5.1.3
nominal size a — — — 6,3 — 10 — 12,5 20 25
Hexagonal output drive
nominal sizeb 3 4 5,5 6,3 8 — 11,2 12,5 — —
Dimensions in accordance with ISO 1174-1. Dimensions in accordance with ISO 1173.
Maximum torque value
N⋅m
4 10 25 30 70 135 200 340 1 000 2 100
Specified torque range
The requirements and methods in this document cover a specified torque range, where the range depends on type and class o f the torque tool.
The torque range or value is selected for the different torque tools as follows.
— Indicating torque tools o f Type I (Classes A, B and D): From the lowest marked value to 100 % o f the
maximum torque value of the respective tool.
— Indicating torque tools o f Type I (Classes C and E): As specified by the manu facturer. — Setting torque tools o f Type II (Classes A, D and G): From the lowest marked value to 100 % o f the
maximum torque value of the respective tool.
— Setting torque tools o f Type II (Classes B, C, E and F): As specified by the manu facturer. 5.1.4
Scales, dials and displays
For scales and dials, the increment between two graduation marks shall not exceed 5 % o f the maximum
torque value of the torque tool.
For electronic displays, the resolution shall not exceed 1/4 o f the maximum permissible relative
deviation of the torque tool at each target value.
For indicating torque tools o f Type I (Classes A, B and D), the scales or dials shall be marked with a zero position. The range between zero and the lowest specified torque value shall be marked on or near the dial or scale in a way to make clear to the user that this range is not within the specified torque range. Alternatively, the scale, dial or display shall be identified in some way to indicate the specified torque
range to the user. 4
© ISO 2017 – All rights reserved
ISO 6789-1:2 017(E)
For indicating torque tools o f Type I (Classes C and E), the range between zero and the lower value o f the range specified by the manu facturer shall be identified in some way to make clear to the user that this range is not in the specified range. The design o f scales, dials and displays has a significant influence on the calibration uncertainty o f a
torque tool. Designers are recommended to take guidance from ISO 6789-2:2017, 6.2.1.
5.1.5
Maximum permissible deviation
Each result for a torque tool, recorded in accordance with Clause 6 and calculated in accordance with Clause 7, shall lie within the respective maximum permissible relative deviation for the type and class of that tool stated in Tables 3 and 4. Where a manufacturer claims a smaller maximum permissible relative deviation than stated in Tables 3 and 4, each result shall lie within the claimed maximum permissible relative deviation. For determining con formance with this subclause, the influence o f the uncertainty o f the torque tool
and of the torque measurement device shall not be considered.
Table 3 — Maximum permissible relative deviation (Type I) Class
A and D B, C and E
Maximum torque value
≤10 N⋅m ±6 %
±6 %
>10 N⋅m ±4 %
If a tool is operating in both directions, the maximum permissible relative deviation shall be met in each direction
specified by the manu facturer.
Table 4 — Maximum permissible relative deviation (Type II) Class
A, B and C D, E, F and G
Maximum torque value
≤10 N⋅m ±6 %
±6 %
>10 N⋅m ±4 %
If a tool is operating in both directions, the maximum permissible relative deviation shall be met in each direction
specified by the manu facturer. 5.1.6
Overloading test
All torque tools to be tested shall be loaded three times in each direction of operation to a torque value
not less than 125 % o f the maximum torque value or at nominal capacity for setting torque tools o f Type II (Classes D, E and F). For Type II (Classes A, C, D, F and G), the test is per formed a fter setting the tool to 100 % o f the maximum torque value. This test does not apply to limiting torque tools.
After the overloading test, the torque tool shall still be within the maximum permissible relative deviation specified in 5.1.5 when tested in accordance with Clause 6 and shall show no physical damage that can be detrimental to the torque tool per formance and sa fety. 5.1.7
Endurance test
All torque tools to be tested shall be cycled at the maximum value, or nominal pre-set torque value for tools o f Type II (Classes B and E), for 5 000 cycles in each direction that the mechanism operates, at a rate between 5 cycles/min and 20 cycles/min.
© ISO 2017 – All rights reserved
5
ISO 6789-1:2017(E)
After the endurance test, the torque tool shall still be within the maximum permissible relative deviation specified in 5.1.5 and shall show no physical damage that can be detrimental to the torque tool per formance and sa fety. 5.1.8
Effect of geometric changes
NOTE Some tools indicate or operate at the same torque value independent of the position of the load application point. Some tools indicate or operate at different torque values depending on the position of the load application. All torque tools to be tested shall be tested for the influence on torque output due to changing geometry, such as but not exclusively flexible head ratchets (see Figure 1) and extension bars designed to be used to reduce operator effort (see Figure 2 ). The manu facturer shall communicate these influences to users
through instruction sheets or the declaration of conformance.
Key
length L 1 length reduced L
F
6
i
g
u
r
e
1
—
E
x
a
m
p
l
e
o
f
a
f
l
e
x
i
b
l
e
h
e
a
d
t
o
r
q
u
e
w
r
e
n
c
h
© ISO 2017 – All rights reserved
ISO 6789-1:2 017(E)
Key
L L2
length length extended Figure 2 — Example of an extension bar
5.2
Quality conformance testing
All torque tools shall be tested during manufacture in accordance with Clause 6. All torque tools that conform with the requirements in 5.1.5 shall either be issued with a declaration of conformance in accordance with Clause 8 or a calibration certificate in accordance with ISO 6789-2. 5.3
Conformance test during use
If the user utilizes procedures for the control of test devices, torque tools shall be included in these procedures. The interval between conformance tests shall be chosen on the basis of the factors of operation such as required maximum permissible deviation, frequency o f use, typical load during operation as well as ambient conditions during operation and storage conditions. The interval shall be adapted according to the procedures specified for the control o f test devices and by evaluating the results gained during successive conformance tests. I f the user does not utilize a control procedure, a period o f 12 months, or 5 000 cycles, whichever occurs first, may be taken as de fault values for the interval between con formance tests. The interval starts with the first use o f the torque tool. A shorter interval between con formance tests may be used i f required by the user, their customer or by
legislation. The torque tool shall be tested for conformance in accordance with 5.2 when it has been subjected to an overload greater than the values given in 5.1.6 , a fter repair or a fter any improper handling which might influence the torque tool per formance and the fulfilment o f the quality con formance requirements.
Conformance tests during use shall be performed in accordance with 5.2 . di fferent specified torque range for the torque tool.
6 6.1
The user may define a
Torque measurement Torque measurement system
The torque measurement system shall be chosen to be suitable for the measurement o f the specified
range of the torque tool. The maximum measurement error of the torque measurement device shall not exceed 1/4 of the claimed maximum permissible relative deviation of the torque tool at each target value.
The torque measurement device shall have a valid calibration certificate traceable to a national standard or to a calibration laboratory meeting the requirements o f ISO/IEC 17025. Alternatively, the torque measurement device shall be calibrated by a laboratory maintaining the national measurement
standard or according to ISO 6789-2:2017, Annex C. © ISO 2017 – All rights reserved
7
ISO 6789-1:2017(E) 6.2 Application of torque 6.2.1 a)
The to rque s hall b e ap p lied by means o f o ne o f the
fo llowing
metho ds .
T he torque to ol i s c au s e d to ro tate ab out the torque me a s urement device a xi s b y the
fol lowi ng:
1) for torque wrenches, a force or two forces with equal value and opposite direction for T-handles, appl ie d to the ha nd le o f the to ol at a con s tant rad i a l d i s tance;
2) for torque screwdrivers, a torque applied to the handle of the tool or two forces with equal value and opposite direction for T-handles. b) The torque measurement device rotates on its measuring axis while a reaction force is applied to the handle of the torque tool. In all cases, each force applied to the tool shall be perpendicular to the axis of rotation. In all cases, the handle of the tool shall be allowed to move in all planes of rotation. T he con ne c tion b e twe en torque me a s urement s ys tem and torque to ol s ha l l p erm it s el f-a l ign ment s o
that parasitic forces and moments are minimized.
The tool to be measured shall be oriented in accordance with Figures 3, 4 or 5. a) In the case of Figures 3 or 4, the operating force, F, shall be applied within the angular deviation 6.2.2
l i m its s p e c i fie d i n the centre o f the hand hold p o s ition o f the grip or o f the marke d lo ad p oi nt.
b) In the case of Figure 5, the operating torque shall be applied within the angular deviation limits s p e ci fie d .
c)
To ol s with fle xible he ad s h a l l b e me a s u re d with the a xi s o f ro tation p er p end ic u l a r to the a xi s o f
the tool.
6.2.3
I ndicating
to rque
to o ls
(Typ e
I)
s hall
be
lo aded
with
an
increas ing
to rque
until
the
target
torque value is indicated on the torque tool. If the torque to be measured has been exceeded, then the
meas urement s hall b e rep eated
fro m
the zero p o s itio n. The time intervals b etween any two s ub s equent
lo adings s hall b e o f the s ame duratio n. S lave p o inters (memo ry indicato rs ) s hall no t b e us ed when taking
the readings. 6.2.4
S etting to rque to o ls (Typ e I I ) s hall b e lo aded with a s lo wly and s teadily increas ing to rque until
attainment o f the target to rque is s ignalled by the to rque to o l. The target to rque s hall b e reached a fter a minimum time as defined in
Table 5.
Table 5 — Minimum time period for application of torque values Applied torque value
Minimum time to increase the f f target value to rque
rom 8 0 % o
ta rge t va lue to