Step by Step Installation OLT ZTE C320 [PDF]

Citation preview

Step By Step Installation OLT ZTE C320 1. Console, CLI and Default Username - Console Connect Cable USB to RS232 > Console Cable > Connect to Port CLI Baud Rate 9600 Enable password is Zxr10 -



Default IP OLT IP Default is 136.1.1.100/16 Connect using straight cable to Port 10/100



-



Default Username Username : zte Password : zte



2. Rack, Shelf, Card and Sub-Card SLOT 1 SLOT 2 SLOT 3 - Added



SLOT 4



ZXAN# config t ZXAN(config)# add-rack rackno 1 racktype C320Rack ZXAN(config)# add-shelf rackno 1 shelfno 1 shelftype C320_SHELF ZXAN(config)# add-card rackno 1 shelfno 1 slotno 1 GTGH ZXAN(config)# add-card rackno 1 shelfno 1 slotno 3 PRAM ZXAN(config)# add-subcard rackno 1 shelfno 1 slotno 4 subcardno 1 UCDC/1 ZXAN(config)# exit ZXAN# write - Query ZXAN# show card Rack Shelf Slot CfgType RealType Port HardVer SoftVer Status ---------------------------------------------------------------------------------------------------------------------------------1 1 1 GTGH GTGH 16 V1.0.0.0 V2.1.0 INSERVICE 1 1 3 PRAM PRAM 3 V1.0.0.0 V1.01 INSERVICE 1 1 1 SMXA SMXA 3 V1.0.0.0 V2.1.0 INSERVICE - Delete ZXAN# conf t ZXAN(config)# del-card slotno 1 Confirm to delete card? [yes/no] : y ZXAN(config)# exit



ZXAN# write 3. Configuring the system time ZXAN# conf t ZXAN(config)# clock timezone GMT 7 ZXAN(config)# exit ZXAN# clock set 10:00:00 jun 22 2019 ZXAN# write 4. User Management Privilege Level 0-1 2-9 10-15



Description When the user logs in and enters operator mode, he can type the enable command and the password to enter privilege mode (privilege level is 15), and uses any commands. When the user logs in and enters the administrator mode, he can use the commands of level 0-9. When the users logs in and enters the administrator mode, he can use the commands of level 0-15. The user can manages user accounts.



ZXAN# conf t ZXAN(config)# username test password Test1234 privilege 15 ZXAN(config)# exit ZXAN# write 5. Hostname ZXAN# conf t ZXAN(config)# hostname ZTE-C320 ZTE-C320(config)# exit ZTE-C320# write 6. Profile (tcont, onu and PON) - Tcont ZXAN# conf t ZXAN(config)# gpon ZXAN(config-gpon)# profile tcont 1g type 3 assured 512 maximum 1024000 ZXAN(config-gpon)# profile tcont 20M type 1 fixed 20480 ZXAN(config-gpon)# exit ZXAN(config)# exit ZXAN# write • Fixed bandwidth (type 1) Type 1 includes only fixed bandwidth. Type 1 has fixed bandwidth and timeslot. It is applicable to the service that to delay and jitter and has fixed or stable flow rate, such as the voice service. • Assured bandwidth (type 2)



Type 2 includes only assured bandwidth. Type 2 has fixed bandwidth but not timeslot. It is applicable to the service that is insensitive to delay and jitter and has limited flow rate, such as the viceo on demand (VOD) service. • Assured and non-assured bandwidths (type 3) Type 3 includes assured and non-assured bandwidths. It has the assured minimum bandwidth and shares the excess bandwidth dynamically. Meanwhile, it is constrained by the maximum bandwidth. It is applicable to the service that requires service assurance but has a large volume of flow burst, such as the subscription download service. • Best-effort bandwidth (type 4) Type 4 includes only best-effort bandwidth. After the fixed bandwidth, assured bandwidth, and non-asswured bandwidth are allocated, type 4 compete for the excess bandwidth. It is applicable to the service that is insensitive to delay and jitter, such as the Web Browse Service. • Support all (type 5) Type 5 combine the four types and has characteristics of the four types. It is applicable to most service streams. -



Onu Profile ZXAN# conf t ZXAN(config)# gpon ZXAN(config-gpon)# onu profile vlan V100 tag-mode tag cvlan 100 pri 1 ZXAN(config-gpon)# exit ZXAN(config)# show gpon onu profile vlan Profile name: V100 Tag mode: tag CVLAN: 100 CVLAN priority:1



-



PON ZXAN# conf t ZXAN(config)# pon ZXAN(config-pon)# onu-type F609 gpon description 4GE, 2Pots, 4Wifi ZXAN(config-pon)# onu-type F609 gpon max-tcont 7 ZXAN(config-pon)# onu-type F609 gpon max-gemport 32 ZXAN(config-pon)# onu-type F609 gpon max-switch-perslot 1 ZXAN(config-pon)# onu-type F609 gpon max-flow-perswitch 32 ZXAN(config-pon)# onu-type-if F609 eth_0/1 ZXAN(config-pon)# onu-type-if F609 eth_0/2 ZXAN(config-pon)# onu-type-if F609 eth_0/3 ZXAN(config-pon)# onu-type-if F609 eth_0/4 ZXAN(config-pon)# onu-type-if F609 pots_0/1 ZXAN(config-pon)# onu-type-if F609 pots_0/2 ZXAN(config-pon)# onu-type-if F609 wifi_0/1 ZXAN(config-pon)# onu-type-if F609 wifi_0/2 ZXAN(config-pon)# onu-type-if F609 wifi_0/3 ZXAN(config-pon)# onu-type-if F609 wifi_0/4 ZXAN(config-pon)# exit ZXAN(config)# show onu-type gpon F609



ONU type name: F609 PON type: gpon Description: 4GE,2POTS,4WIFI Max T-CONT: 7 Max GEM port: 32 Max switch per slot: 1 Max flow per switch: 32 Max IP host: 2 Max IPv6 host: 0 Service ability N:1: support Service ability 1:M: support Service ability 1:P: support WIFI mgmt via non OMCI: disable OMCI send mode: async Default multicast range:none VRG: disable MGC configure mode: zte Max VEIP: 0(default: 1 VEIP) Extended OMCI: disable Location: disable 7. Installation ONU



Connect Onu to OLT - Query the unauthenticated ONU ZXAN#conf t ZXAN(config)# show gpon onu uncfg OnuIndex Sn State gpon-onu_1/1/1:1 ZTEGC1E5FE05 unknown ZXAN(config)# interface gpon-olt_1/1/1 ZXAN(config-if)# onu 1 type F609 sn ZTEGC1E5FE05 ZXAN(config-if)# exit ZXAN(config)# show gpon onu state gpon-olt_1/1/1 OnuIndex Admin State OMCC State Phase State Channel -------------------------------------------------------------1/1/1:1 enable disable OffLine 1(GPON)



State Offline Logging syncMib Working LOS DyingGasp -



Description The OLT does not find the ONU because the ONU is offline The OLT has found the ONU and is measuring the distance The OLT has measured the distance to the ONU and is synchronizing data The data synchronization completes, and you can configure services The fiber link between the OLT and ONU is Faulty so that the ONU is offline The ONU is powered off



Show receive power of both olt and onu/ont ZXAN# show pon power attenuation gpon-onu_1/1/1:1 OLT ONU Attenuation --------------------------------------------------------------------------------------------------------------------------------Up Rx : -11.060(dbm) Tx : 2.567(dbm) 13.627(dB) Down Tx : 3.813(dbm) Rx : -14.480(dbm) 18.2939dB)



-



Cofiguring the GPON Broadband Service (PPPoE)



ZXAN(config)# vlan 100 ZXAN(config-vlan100)# description Broadband-Service ZXAN(config-vlan100)# exit ZXAN(config)# interface gei_1/4/3 ZXAN(config-if)# switchport vlan 100 tag ZXAN(config-if)# exit ZXAN(config)# interface gpon-onu_1/1/1:1 ZXAN(config-if)# tcont 1 profile 1G ZXAN(config-if)# gemport 1 tcont 1 ZXAN(config-if)# service-port 1 vport 1 user-vlan 100 vlan 100 ZXAN(config-if)# exit ZXAN(config)# pon-onu-mng gpon-onu_1/1/1:1 ZXAN(gpon-onu-mng 1/1/1:1)# service INTERNET gemport 1 vlan 100 ZXAN(gpon-onu-mng 1/1/1:1)# wan-ip 1 mode pppoe username test password test vlan-profile V100 host 1 ZXAN(gpon-onu-mng 1/1/1:1)# exit ZXAN(config)# exit ZXAN# write ZXAN# show gpon remote-onu ip-host gpon-onu_1/1/1:1 Host ID: 1



Host name: Identify: IP address: Mask: Gateway: Primary DNS: Second DNS: DHCP enable: PING response: Traceroute response: MAC address: Current IP address: Current mask: Current gateway: Current primary DNS: Current second DNS: Domain name:



omci_ipv4_pppoe_1 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 disable disable disable 9c6f.52e2.2d70 10.173.3.248 255.255.255.255 10.172.3.1 10.172.3.1 203.190.55.217



-



Show pon olt config ZXAN# show running-config interface gpon-olt_1/1/1 Building configuration. . . Interface gpon-olt_1/1/1 no shutdown linkstrap disable onu 1 type F609 sn ZTEGC1E5FE05



-



Show onu configuration ZXAN# show run interface gpon-onu_1/1/1:1 Building configuration… interface gpon-onu_1/1/1:1 tcont 1 profile 1G gemport 1 tcont 1 service-port 1 vport 1 user-vlan 100 vlan 100 ZXAN# show onu running config gpon-onu_1/1/1:1 pon-onu-mng gpon-onu_1/1/1:1 service INTERNET gemport 1 vlan 100 wan-ip 1 mode pppoe username test password test vlan-profile V100 host 1



-



Configuring ONU Multicast Service



ZXAN# conf t ZXAN(config)# vlan 200 ZXAN(config-vlan200)# descriprion MULTICAST-SERVICES ZXAN(config-vlan200)# exit ZXAN(config)# interface gei_1/4/3 ZXAN(config-if)# switchport vlan 200 tag ZXAN(config-if)# exit ZXAN(config)# interface gpon-onu_1/1/1:1 ZXAN(config-if)# tcont 2 profile 20M ZXAN(config-if)# gemport 2 tcont 2 ZXAN(config-if)# service-port 2 vport 2 user-vlan 200 vlan 200 ZXAN(config-if)# igmp fast-leave enable vport 2 ZXAN(config-if)# exit ZXAN(config)# pon-onu-mng gpon-onu_1/1/1:1 ZXAN(gpon-onu-mng 1/1/1:1)# service IPTV gemport 2 vlan 200 ZXAN(gpon-onu-mng 1/1/1:1)# vlan port eth_0/4 mode tag vlan 200 ZXAN(gpon-onu-mng 1/1/1:1)# dhcp-ip ethuni eth_0/4 from-internet ZXAN(gpon-onu-mng 1/1/1:1)# mvlan 200 ZXAN(config)# igmp enable ZXAN(config)# igmp mvlan 200 ZXAN(config)# igmp mvlan 200 group 224.1.1.1 to 224.1.1.3 ZXAN(config)# igmp mvlan 200 source-port gei_1/4/3 ZXAN(config)# igmp mvlan 200 receive-port gpon-onu_1/1/1:1 vport 2