13 0 106 KB
Коды ошибок (STATUS_SVC+0) //USB Chip. After 0.5S,USB chip not normal started,Maybe USB chip SVC 00 damaged (STATUS_SVC+1) //FPGA chip 1. state continues for high when power on,Maybe USB SVC 01 chip damaged (STATUS_SVC+2) //FPGA chip 2. After power down n configuration,but n configuration SVC 02 still high SVC 03 (STATUS_SVC+3) //FPGA chip 3. n configuration , However, the n state to maintain high (STATUS_SVC+4) //FPGA chip 4. When configuring the FPGA, the FPGA reports an error or SVC 04 retry 10 times SVC 05 (STATUS_SVC+5) //Motherboard upgrade failed SVC 06 (STATUS_SVC+6) //Board has not been factory initialization SVC 07 (STATUS_SVC+16) //Did not pass the factory tools to detect memory SVC 08 (STATUS_SVC+7) //Synchronous dynamic memory test did not pass SVC 09 (STATUS_SVC+8) //Can not read the FPGA from flash (STATUS_SVC+9) //Synchronous dynamic memory is too small to support the current SVC 10 settings SVC 11 (STATUS_SVC+10) //Read board ID error. Actually operating encryption chip failure SVC 12 (STATUS_SVC+11) //The system of ARM request initialization error. (STATUS_SVC+12) //The carriage board failed to initialize, in fact, the EPSON head board SVC 13 operating encryption chip failure FTA 00 (STATUS_FTA+0) //Abnormal restart of USB chip FTA 01 (STATUS_FTA+1) //Print data format error FTA 02 (STATUS_FTA+2) //Error print data format size FTA 03 (STATUS_FTA+3) //Print job should not be included with the additional data FTA 04 (STATUS_FTA+4) //Pass quantity of data and the actual number of pass Data do not match FTA 05 (STATUS_FTA+5) //The serial data format does not FTA 06 (STATUS_FTA+6) //One pass is completed DMAO still at work FTA 07 (STATUS_FTA+7) //Printing errors in the initial print position or end position FTA 08 (STATUS_FTA+8) //Pass print starting point less than the origin (STATUS_FTA+9) //Image end position beyond the printer farthest point, the job size is too FTA 09 wide FTA 10 (STATUS_FTA+10) //Motion control first phase of initialization does not pass FTA 11 (STATUS_FTA+11) //Motion control of the second phase of initialization does not pass FTA 12 (STATUS_FTA+12) //Initialization of the first stage of carriage board did not pass FTA 13 (STATUS_FTA+13) //Initialization of the second stage of carriage board did not pass (STATUS_FTA+14) //The Main Board LVDS receiver chip is not locked, or the cable is not FTA 14 plugged FTA 15 (STATUS_FTA+15) //Pass definition of the direction of value beyond the defined FTA 16 (STATUS_FTA+16) //The update failed: Motherboard write stage FTA 17 (STATUS_FTA+17) //Failed to read the read‐only memory FTA 18 (STATUS_FTA+18) //Failed to write to read‐only memory FTA 19 (STATUS_FTA+19) //Board has not been factory initialization settings FTA 20 (STATUS_FTA+20) //carriage board is restarted
FTA 21 (STATUS_FTA+21) //Spectra high voltage board failed to initialize (STATUS_FTA+22) //Head types reported by carriage board and factory set do not match, FTA 22 please replace the carriage board or reconfigure hardware settings. (STATUS_FTA+23) //The control system and the software version of the manufacturers do FTA 23 not match, need to be replaced or upgraded versions of the system FTA 24 (STATUS_FTA+24) //Over time, please re‐enter the password FTA 25 (STATUS_FTA+25) //Internal error, a blank pass or Y‐axis doesn't feed medium FTA 26 (STATUS_FTA+26) //Connect to the USB1.1 / / this is a fatal error (STATUS_FTA+27) //the language and authority which software using are not match, FTA 27 please re‐setting language or re‐enter the password FTA 28 (STATUS_FTA+28) //PINCONF written to the FPGA error FTA 29 (STATUS_FTA+29) //Factory tools failed to write the number of colours FTA 30 (STATUS_FTA+30) //Carriage board memory write error FTA 31 (STATUS_FTA+31) ////Head heated over 55 degrees, all heating were forced to close. FTA 32 (STATUS_FTA+32) //Software error or wrong version, not by the handshake protocol FTA 33 (STATUS_FTA+33) //Firmware requires special software version, version error. FTA 34 (STATUS_FTA+34) //The current system does not support two color in one head FTA 35 (STATUS_FTA+35) //Over the ink dosage limit, please re‐enter the password FTA 36 (STATUS_FTA+36) //Firmware requires software version supports ink code, version error FTA 37 (STATUS_FTA+37) //The EPSON head error. (STATUS_FTA+38) //EPSON carriage board FPGA error. Usually overclocking or data to be FTA 38 interference FTA 39 (STATUS_FTA+39) //ID of writing board error FTA 40 (STATUS_FTA+40) //The factory initialization setting error ERR 00 (STATUS_ERR+0) //EP0 command is interrupted ERR 01 (STATUS_ERR+1) //Connect to the USB1 export / / this is a fatal error ERR 02 (STATUS_ERR+3) //Carriage board and main board communication timeout ERR 03 (STATUS_ERR+2) //Sports communication timeout ERR 04 (STATUS_ERR+4) //Pass data did not finish printing (STATUS_ERR+5) //Print data is less than the number of invalid procedure or trigger ERR 05 ignition ERR 06 (STATUS_ERR+6) //Print data is greater than the number of ignition ERR 07 (STATUS_ERR+7) ERR 08 (STATUS_ERR+8)//Internal state ERR 09 (STATUS_ERR+9) //FPGA Received error (STATUS_ERR+10) //Moving too fast or uneven, the data are transmitting, but ignition ERR 10 command (STATUS_ERR+11) //did not receive the movement command completion after motion ERR 11 command is issued for 30 seconds (STATUS_ERR+12) //Errors in the automatic cleaning command, should not have ERR 12 happened ERR 13 (STATUS_ERR+13) //Errors in the automatic cleaning command, should not have
happened ERR 120 (STATUS_ERR+) //Debug state 1 ERR 121 (STATUS_ERR+0x51) //Debug state 1 INI 00 (STATUS_INI+0) //Control board is being initialized INI 01 (STATUS_INI+1) //Initializing the USB communication INI 02 (STATUS_INI+2) //Is initialized FPGA INI 03 (STATUS_INI+3)//Initializing exercise INI 04 (STATUS_INI+4) //carriage board is being initialized INI 05 (STATUS_INI+5) //Spectra high voltage board is being initialized